Electronic Components Datasheet Search |
|
AT45DB081B-CC-2.5 Datasheet(PDF) 3 Page - ATMEL Corporation |
|
|
AT45DB081B-CC-2.5 Datasheet(HTML) 3 Page - ATMEL Corporation |
3 / 32 page 3 AT45DB081B 2225C–12/01 Memory Architecture Diagram Device Operation The device operation is controlled by instructions from the host processor. The list of instructions and their associated opcodes are contained in Tables 1 through 4. A valid instruction starts with the falling edge of CS followed by the appropriate 8-bit opcode and the desired buffer or main memory address location. While the CS pin is low, tog- gling the SCK pin controls the loading of the opcode and the desired buffer or main memory address location through the SI (serial input) pin. All instructions, addresses and data are transferred with the most significant bit (MSB) first. Buffer addressing is referenced in the datasheet using the terminology BFA8 - BFA0 to denote the nine address bits required to designate a byte address within a buffer. Main memory addressing is referenced using the terminology PA11 - PA0 and BA8 - BA0 where PA11 - PA0 denotes the 12 address bits required to designate a page address and BA8 - BA0 denotes the nine address bits required to designate a byte address within the page. Read Commands By specifying the appropriate opcode, data can be read from the main memory or from either one of the two data buffers. The DataFlash supports two categories of read modes in relation to the SCK signal. The differences between the modes are in respect to the inactive state of the SCK signal as well as which clock cycle data will begin to be output. The two categories, which are comprised of four modes total, are defined as Inactive Clock Polarity Low or Inactive Clock Polarity High and SPI Mode 0 or SPI Mode 3. A separate opcode (refer to Table 1 on page 10 for a complete list) is used to select which category will be used for reading. Please refer to the “Detailed Bit-level Read Timing” diagrams in this datasheet for details on the clock cycle sequences for each mode. CONTINUOUS ARRAY READ: By supplying an initial starting address for the main memory array, the Continuous Array Read command can be utilized to sequentially read a continuous stream of data from the device by simply providing a clock signal; no additional addressing information or control signals need to be provided. The DataFlash incorporates an internal address counter that will automatically increment on every clock SECTOR 0 = 8 Pages 2112 bytes (2K + 64) SECTOR 1 = 248 Pages 65,472 bytes (62K + 1984) Block = 2112 bytes (2K + 64) 8 Pages SECTOR 0 Page = 264 bytes (256 + 8) PAGE 0 PAGE 1 PAGE 6 PAGE 7 PAGE 8 PAGE 9 PAGE 4094 PAGE 4095 PAGE 14 PAGE 15 PAGE 16 PAGE 17 PAGE 18 PAGE 4093 SECTOR ARCHITECTURE BLOCK ARCHITECTURE PAGE ARCHITECTURE BLOCK 0 BLOCK 1 BLOCK 30 BLOCK 31 BLOCK 32 BLOCK 33 BLOCK 510 BLOCK 511 BLOCK 62 BLOCK 63 BLOCK 64 BLOCK 65 SECTOR 8 = 512 Pages 135,168 bytes (128K + 4K) BLOCK 2 SECTOR 2 = 256 Pages 67,584 bytes (64K + 2K) SECTOR 3 = 512 Pages 135,168 bytes (128K + 4K) SECTOR 4 = 512 Pages 135,168 bytes (128K + 4K) SECTOR 9 = 512 Pages 135,168 bytes (128K + 4K) |
Similar Part No. - AT45DB081B-CC-2.5 |
|
Similar Description - AT45DB081B-CC-2.5 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.CO.NZ |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |