PIC18F4520ESLASHMLQTP datasheet(188/390 Pages) MICROCHIP

188 / 390 page

PIC18F2420/2520/4420/4520

DS39631A-page 186

Preliminary

 2004 Microchip Technology Inc.

17.4.6.1

I2C Master Mode Operation

The master device generates all of the serial clock

pulses and the Start and Stop conditions. A transfer is

ended with a Stop condition or with a Repeated Start

condition. Since the Repeated Start condition is also

the beginning of the next serial transfer, the I2C bus will

not be released.

In Master Transmitter mode, serial data is output

through SDA, while SCL outputs the serial clock. The

first byte transmitted contains the slave address of the

receiving device (7 bits) and the Read/Write (R/W) bit.

In this case, the R/W bit will be logic ‘0’. Serial data is

transmitted 8 bits at a time. After each byte is transmit-

ted, an Acknowledge bit is received. Start and Stop

conditions are output to indicate the beginning and the

end of a serial transfer.

In Master Receive mode, the first byte transmitted con-

tains the slave address of the transmitting device

(7 bits) and the R/W bit. In this case, the R/W bit will be

logic ‘1’. Thus, the first byte transmitted is a 7-bit slave

address followed by a ‘1’ to indicate the receive bit.

Serial data is received via SDA, while SCL outputs the

serial clock. Serial data is received 8 bits at a time. After

each byte is received, an Acknowledge bit is transmit-

ted. Start and Stop conditions indicate the beginning

and end of transmission.

The Baud Rate Generator used for the SPI mode

operation is used to set the SCL clock frequency for

either 100 kHz, 400 kHz or 1 MHz I2C operation. See

Section 17.4.7 “Baud Rate” for more detail.

A typical transmit sequence would go as follows:

The user generates a Start condition by setting

the Start Enable bit, SEN (SSPCON2<0>).

SSPIF is set. The MSSP module will wait the

required start time before any other operation

takes place.

The user loads the SSPBUF with the slave

address to transmit.

Address is shifted out the SDA pin until all 8 bits

are transmitted.

The MSSP module shifts in the ACK bit from the

slave device and writes its value into the

SSPCON2 register (SSPCON2<6>).

The MSSP module generates an interrupt at the

end of the ninth clock cycle by setting the SSPIF

bit.

The user loads the SSPBUF with eight bits of

data.

Data is shifted out the SDA pin until all 8 bits are

transmitted.

The MSSP module shifts in the ACK bit from the

slave device and writes its value into the

SSPCON2 register (SSPCON2<6>).

10. The MSSP module generates an interrupt at the

end of the ninth clock cycle by setting the SSPIF

bit.

11. The user generates a Stop condition by setting

the Stop Enable bit, PEN (SSPCON2<2>).

12. Interrupt is generated once the Stop condition is

complete.

PIC18F4520E/MLQTP Datasheet(PDF) 188 Page - Microchip Technology

PIC18F4520E/MLQTP Datasheet(HTML) 188 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL