AT89C51CC03U-RDTIM datasheet(170/197 Pages) ATMEL

170 / 197 page

170

AT89C51CC03

4182K–CAN–05/06

Notes:

1. Operating I

CC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 81.), VIL =

SS + 0.5V,

VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used (see Figure

78.).

2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5V, VIH = VCC -

0.5V; XTAL2 N.C; Port 0 = VCC; EA = RST = VSS (see Figure 79.).

3. Power-down I

CC is measured with all output pins disconnected; EA = VCC, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Fig-

ure 80.). In addition, the WDT must be inactive and the POF flag must be set.

4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1

and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0

transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed

0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary.

5. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature.

6. Under steady state (non-transient) conditions, I

OL must be externally limited as follows:

Maximum IOL per port pin: 10 mA

Maximum IOL per 8-bit port:

Port 0: 26 mA

Ports 1, 2, 3 and 4: 15 mA

Maximum total I

OL for all output pins: 71 mA

If I

OL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater

than the listed test conditions.

VOH

Output High Voltage, ports 1, 2, 3, and 4

VCC - 0.3

VCC - 0.7

VCC - 1.5

IOH = -10 μA

IOH = -30 μA

IOH = -60 μA

VCC = 3V to 5.5V

VOH1

Output High Voltage, port 0, ALE, PSEN

VCC - 0.3

VCC - 0.7

VCC - 1.5

IOH = -200 μA

IOH = -3.2 mA

IOH = -7.0 mA

VCC = 5V ± 10%

RRST

RST Pulldown Resistor

100

200

IIL

Logical 0 Input Current ports 1, 2, 3 and 4

-50

μA

Vin = 0.45V

ILI

Input Leakage Current

±10

μA0.45V < Vin < V

ITL

Logical 1 to 0 Transition Current, ports 1, 2, 3

and 4

-650

μA

Vin = 2.0V

Capacitance of I/O Buffer

Fc = 1 MHz

TA = 25

°C

IPD

Power-down Current Industrial

150

μA3V < V

CC < 5.5V

(3)

Power-down Current Automotive

100

350

μA3V < V

CC < 5.5V

(3)

Power Supply Current

CCOP = 0.4 Frequency (MHz) + 8

CCIDLE = 0.2 Frequency (MHz) + 8

Vcc = 5.5V(1)(2)

ICCWRITE

Power Supply Current on flash or EEdata write

0.8 x

Frequency

(MHz) + 15

VCC = 5.5V

Table 116. DC Parameters in Standard Voltage (Continued)

Symbol

Parameter

Min

Typ(5)

Max

Unit

Test Conditions

AT89C51CC03U-RDTIM Datasheet(PDF) 170 Page - ATMEL Corporation

AT89C51CC03U-RDTIM Datasheet(HTML) 170 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL