PIC24FJ256GA705-ISLASHM4. datasheet(328/412 Pages) MICROCHIP

328 / 412 page

PIC24FJ256GA705 FAMILY

DS30010118B-page 328

 2016 Microchip Technology Inc.

HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER

R/W-0

U-0

R/W-0

U-0

R/W-0

HS, HC, R-0 HS, HC, R-0 HS, HC, R-0

HLVDEN

—LSIDL

—

VDIR

BGVST

IRVST

LVDEVT(2)

bit 15

bit 8

U-0

R/W-0

—

HLVDL3

HLVDL2

HLVDL1

HLVDL0

bit 7

bit 0

Legend:

HS = Hardware Settable bit

HC = Hardware Clearable bit

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 15

HLVDEN:

High/Low-Voltage Detect Power Enable bit

= HLVD is enabled

= HLVD is disabled

bit 14

Unimplemented:

Read as ‘0’

bit 13

LSIDL:

HLVD Stop in Idle Mode bit

= Discontinues module operation when device enters Idle mode

= Continues module operation in Idle mode

bit 12

Unimplemented:

Read as ‘0’

bit 11

VDIR:

Voltage Change Direction Select bit

= Event occurs when voltage equals or exceeds trip point (HLVDL<3:0>)

= Event occurs when voltage equals or falls below trip point (HLVDL<3:0>)

bit 10

BGVST:

Band Gap Voltage Stable Flag bit

= Indicates that the band gap voltage is stable

= Indicates that the band gap voltage is unstable

bit 9

IRVST:

Internal Reference Voltage Stable Flag bit

= Internal reference voltage is stable; the High-Voltage Detect logic generates the interrupt flag at the

specified voltage range

= Internal reference voltage is unstable; the High-Voltage Detect logic will not generate the interrupt

flag at the specified voltage range and the HLVD interrupt should not be enabled

bit 8

LVDEVT:

Low-Voltage Event Status bit(2)

= LVD event is true during current instruction cycle

= LVD event is not true during current instruction cycle

bit 7-4

Unimplemented:

Read as ‘0’

bit 3-0

HLVDL<3:0>:

High/Low-Voltage Detection Limit bits

1111

= External analog input is used (input comes from the HLVDIN pin)

1110

= Trip Point 1(1)

1101

= Trip Point 2(1)

1100

= Trip Point 3(1)

•

0100

= Trip Point 11(1)

00xx

= Unused

Note 1:

For the actual trip point, see Section 32.0 “Electrical Characteristics”.

The LVDIF flag cannot be cleared by software unless LVDEVT = 0. The voltage must be monitored so that

the HLVD condition (as set by VDIR and HLVDL<3:0>) is not asserted.

PIC24FJ256GA705-I/M4. Datasheet(PDF) 328 Page - Microchip Technology

PIC24FJ256GA705-I/M4. Datasheet(HTML) 328 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL