M16CSLASH62 datasheet(618/621 Pages) RENESAS

618 / 621 page

Contents for change

Revision

date

Version

Revision history

Mitsubishi microcomputers

M16C / 62 Group

SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

M16C/62 User's Manual

603

99.12.1

Page 463 Figure 3.2.4 Setting One-shot timer's time

3F16 --> 4016.

Page 465 Figure 3.3.1

000016 --> 000116.

Page 559 to 562 Figure 7.1.5, Figure 7.1.6, Figure 7.2.1 and Figure 7.2.2

All changed

Page 560

Add to Figure 7.1.7

Page 567 to 601

Add to Appendix.

Page 151 Note 2

• Before data can be written to the SI/Oi transmit/receive register (addresses

036016, 036416), the CLKi pin input must be in the low state. Also, before rewriting

the SI/Oi Control Register (addresses 036216, 036616)’s bit 7 (SOUTi initial value

set bit), make sure the CLKi pin input is held low. ---> • Before data can be written

to the SI/Oi transmit/receive register (addresses 036016, 036416), the CLKi pin

input must be in the high state. Also, before rewriting the SI/Oi Control Register

(addresses 036216, 036616)’s bit 7 (SOUTi initial value set bit), make sure the CLKi

pin input is held high.

99.12.21

REV.C1

REV.C

REV.C2

00.7.4

Page 35, Table 1.12.2

_______

Normal mode, microprocessor mode, CS0 area

0300016 to FFFFF16 --->3000016 to FFFFF16

_______

Expansion mode 1, microprocessor mode, PM13=1, CS0 area

0600016 to FFFFF16 --->0600016 to BFFFF16

Page 50, Figure 1.13.6

Note: Writing a value to an address after “1” is written to this bit returns the bit to

“0” . Other bits do not automatically return to “0” and they must therefore

be reset by the program.

Page 150, Figure 1.19.32, bit 5 of the SI/Oi control register (i=3, 4)

Transfer direction lect bit --->Transfer direction select bit

Page 150, Figure 1.19.32, Note 2

When using the port as an input/output port by setting the SI/Oi port select bit (i =

3, 4) to “1”, be sure to set the sync clock select bit to “1”.

--->

When using the port as an input/output port by setting the SI/Oi port select bit (i =

3, 4) to “0”, be sure to set the sync clock select bit to “1”.

M16C/62 Datasheet(PDF) 618 Page - Renesas Technology Corp

M16C/62 Datasheet(HTML) 618 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL