PIC18F4580-ESLASHML datasheet(425/490 Pages) MICROCHIP

425 / 490 page

DS39637D-page 425

PIC18F2480/2580/4480/4580

Supply Current (IDD)(2,3)

PIC18LF2X80/4X80

μA

-40°C

VDD = 2.0V

FOSC = 31 kHz

(RC_RUN mode,

Internal oscillator source)

μA+25°C

μA+85°C

PIC18LF2X80/4X80

μA

-40°C

VDD = 3.0V

μA+25°C

μA+85°C

All devices

150

170

μA

-40°C

VDD = 5.0V

113

170

μA+25°C

170

μA+85°C

Extended devices only

170

280

μA

+125°C

PIC18LF2X80/4X80

530

1030

μA

-40°C

VDD = 2.0V

FOSC = 1 MHz

(RC_RUN mode,

Internal oscillator source)

550

1030

μA+25°C

560

1030

μA+85°C

PIC18LF2X80/4X80

940

1150

μA

-40°C

VDD = 3.0V

900

1150

μA+25°C

880.0

1150

μA+85°C

All devices

1.8

2.3

-40°C

VDD = 5.0V

1.7

2.3

+25°C

1.7

2.3

+85°C

Extended devices only

2.6

3.6

+125°C

28.2

DC Characteristics:

Power-Down and Supply Current

PIC18F2480/2580/4480/4580 (Industrial, Extended)

PIC18LF2480/2580/4480/4580 (Industrial) (Continued)

PIC18LF2480/2580/4480/4580

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

PIC18F2480/2580/4480/4580

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

-40°C

≤ TA ≤ +125°C for extended

Param

No.

Device

Typ

Max

Units

Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the

part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current

disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the

current consumption.The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula, Ir = VDD/2REXT (mA), with REXT in k

Ω.

4: Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

PIC18F4580-E/ML Datasheet(PDF) 425 Page - Microchip Technology

PIC18F4580-E/ML Datasheet(HTML) 425 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL