PIC18F4580-ESLASHML datasheet(146/490 Pages) MICROCHIP

146 / 490 page

PIC18F2480/2580/4480/4580

DS39637D-page 146

11.5

PORTE, TRISE and LATE

Registers

Depending on the particular PIC18F2480/2580/4480/

4580 device selected, PORTE is implemented in two

different ways.

For PIC18F4X80 devices, PORTE is a 4-bit wide port.

Three pins (RE0/RD/AN5, RE1/WR/AN6/C1OUT and

RE2/CS/AN7/C2OUT) are individually configurable as

inputs or outputs. These pins have Schmitt Trigger

input buffers. When selected as an analog input, these

pins will read as ‘0’s.

The corresponding Data Direction register is TRISE.

Setting a TRISE bit (= 1) will make the corresponding

PORTE pin an input (i.e., put the corresponding output

driver in a high-impedance mode). Clearing a TRISE bit

(= 0) will make the corresponding PORTE pin an output

(i.e., put the contents of the output latch on the selected

pin).

TRISE controls the direction of the RE pins, even when

they are being used as analog inputs. The user must

make sure to keep the pins configured as inputs when

using them as analog inputs.

The upper four bits of the TRISE register also control

the operation of the Parallel Slave Port. Their operation

is explained in Register 11-1.

The Output Latch register (LATE) is also memory

mapped. Read-modify-write operations on the LATE

PORTE.

The fourth pin of PORTE (MCLR/VPP/RE3) is an input

only pin. Its operation is controlled by the MCLRE

Configuration bit. When selected as a port pin

(MCLRE = 0), it functions as a digital input only pin. As

such, it does not have TRIS or LAT bits associated with

its operation. Otherwise, it functions as the device’s

Master Clear input. In either configuration, RE3 also

functions as the programming voltage input during

programming.

EXAMPLE 11-5:

INITIALIZING PORTE

11.5.1

PORTE IN 28-PIN DEVICES

For PIC18F2X80 devices, PORTE is only available

when

Master

Clear

functionality

disabled

(MCLRE = 0). In these cases, PORTE is a single bit,

input only port comprised of RE3 only. The pin operates

as previously described.

Note:

On a Power-on Reset, RE<2:0> are

configured as analog inputs.

Note:

On a Power-on Reset, RE3 is enabled as

a digital input only if Master Clear

functionality is disabled.

CLRF

PORTE

; Initialize PORTE by

; clearing output

; data latches

CLRF

LATE

; Alternate method

; to clear output

; data latches

MOVLW

0Ah

; Configure A/D

MOVWF

ADCON1 ; for digital inputs

MOVLW

03h

; Value used to

; initialize data

; direction

MOVLW

07h

; Turn off

MOVWF

CMCON

; comparators

MOVWF

TRISC

; Set RE<0> as inputs

; RE<1> as outputs

; RE<2> as inputs

PIC18F4580-E/ML Datasheet(PDF) 146 Page - Microchip Technology

PIC18F4580-E/ML Datasheet(HTML) 146 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL