PIC18F2610-ESLASHML datasheet(137/376 Pages) MICROCHIP

137 / 376 page

DS39636D-page 139

PIC18F2X1X/4X1X

15.0 ENHANCED CAPTURE/

COMPARE/PWM (ECCP)

MODULE

In PIC18F4410/4415/4510/4515/4610 devices, CCP1

is implemented as a standard CCP module with

enhanced PWM capabilities. These include the

provision for 2 or 4 output channels, user selectable

polarity, dead-band control and automatic shutdown

and restart. The Enhanced features are discussed in

detail in Section 15.4 “Enhanced PWM Mode”.

Capture, Compare and single-output PWM functions of

the ECCP module are the same as described for the

standard CCP module.

The control register for the Enhanced CCP module is

shown in Register 15-1. It differs from the CCPxCON

registers

PIC18F2410/2415/2510/2515/2610

devices in that the two Most Significant bits are

implemented to control PWM functionality.

CCP1CON REGISTER (ECCP1 MODULE, 40/44-PIN DEVICES)

Note:

The ECCP module is implemented only in

40/44-pin devices.

R/W-0

P1M1

P1M0

DC1B1

DC1B0

CCP1M3

CCP1M2

CCP1M1

CCP1M0

bit 7

bit 0

bit 7-6

P1M1:P1M0: Enhanced PWM Output Configuration bits

If CCP1M3:CCP1M2 = 00, 01, 10:

xx = P1A assigned as Capture/Compare input/output; P1B, P1C, P1D assigned as port pins

If CCP1M3:CCP1M2 = 11:

00 = Single output: P1A modulated; P1B, P1C, P1D assigned as port pins

01 = Full-bridge output forward: P1D modulated; P1A active; P1B, P1C inactive

10 = Half-bridge output: P1A, P1B modulated with dead-band control; P1C, P1D assigned

as port pins

11 = Full-bridge output reverse: P1B modulated; P1C active; P1A, P1D inactive

bit 5-4

DC1B1:DC1B0: PWM Duty Cycle bit 1 and bit 0

Capture mode:

Unused.

Compare mode:

Unused.

PWM mode:

These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are

found in CCPR1L.

bit 3-0

CCP1M3:CCP1M0: Enhanced CCP Mode Select bits

0000 = Capture/Compare/PWM off (resets ECCP module)

0001 = Reserved

0010 = Compare mode, toggle output on match

0011 = Capture mode

0100 = Capture mode, every falling edge

0101 = Capture mode, every rising edge

0110 = Capture mode, every 4th rising edge

0111 = Capture mode, every 16th rising edge

1000 = Compare mode, initialize CCP1 pin low, set output on compare match (set CCP1IF)

1001 = Compare mode, initialize CCP1 pin high, clear output on compare match (set CCP1IF)

1010 = Compare mode, generate software interrupt only, CCP1 pin reverts to I/O state

1011 = Compare mode, trigger special event (ECCP resets TMR1 or TMR3, sets CC1IF bit)

1100 = PWM mode; P1A, P1C active-high; P1B, P1D active-high

1101 = PWM mode; P1A, P1C active-high; P1B, P1D active-low

1110 = PWM mode; P1A, P1C active-low; P1B, P1D active-high

1111 = PWM mode; P1A, P1C active-low; P1B, P1D active-low

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

PIC18F2610-E/ML Datasheet(PDF) 137 Page - Microchip Technology

PIC18F2610-E/ML Datasheet(HTML) 137 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL