| Electronic Components Datasheet Search |
|
DSPIC33FJ64GP706 Datasheet(PDF) 167 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
DSPIC33FJ64GP706 Datasheet(HTML) 167 Page - Microchip Technology |
|
167 / 322 page ![]() © 2009 Microchip Technology Inc. DS70286C-page 165 dsPIC33FJXXXGPX06/X08/X10 14.0 INPUT CAPTURE The input capture module is useful in applications requiring frequency (period) and pulse measurement. The dsPIC33FJXXXGPX06/X08/X10 devices support up to eight input capture channels. The input capture module captures the 16-bit value of the selected Time Base register when an event occurs at the ICx pin. The events that cause a capture event are listed below in three categories: 1. Simple Capture Event modes -Capture timer value on every falling edge of input at ICx pin -Capture timer value on every rising edge of input at ICx pin 2. Capture timer value on every edge (rising and falling) 3. Prescaler Capture Event modes -Capture timer value on every 4th rising edge of input at ICx pin -Capture timer value on every 16th rising edge of input at ICx pin Each input capture channel can select between one of two 16-bit timers (Timer2 or Timer3) for the time base. The selected timer can use either an internal or external clock. Other operational features include: • Device wake-up from capture pin during CPU Sleep and Idle modes • Interrupt on input capture event • 4-word FIFO buffer for capture values - Interrupt optionally generated after 1, 2, 3 or 4 buffer locations are filled • Input capture can also be used to provide additional sources of external interrupts FIGURE 14-1: INPUT CAPTURE BLOCK DIAGRAM Note: This data sheet summarizes the features of the dsPIC33FJXXXGPX06/X08/X10 family of devices. However, it is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 12. “Input Capture” (DS70198) in the “dsPIC33F Family Reference Manual”, which is available from the Microchip web site (www.microchip.com). Note: Only IC1 and IC2 can trigger a DMA data transfer. If DMA data transfers are required, the FIFO buffer size must be set to 1 (ICI<1:0> = 00). ICxBUF ICx Pin ICM<2:0> (ICxCON<2:0>) Mode Select 3 10 Set Flag ICxIF (in IFSn Register) TMRy TMRz Edge Detection Logic 16 16 FIFO R/W Logic ICxI<1:0> ICOV, ICBNE (ICxCON<4:3>) ICxCON Interrupt Logic System Bus From 16-bit Timers ICTMR (ICxCON<7>) Prescaler Counter (1, 4, 16) and Clock Synchronizer Note: An ‘x’ in a signal, register or bit name denotes the number of the capture channel. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |