STM32F303XD datasheet(117/173 Pages) STMICROELECTRONICS

117 / 173 page

DocID026415 Rev 5

117/173

STM32F303xD STM32F303xE

Electrical characteristics

151

Static latch-up

Two complementary static tests are required on six parts to assess the latch-up

performance:

•

A supply overvoltage is applied to each power supply pin

•

A current injection is applied to each input, output and configurable I/O pin

These tests are compliant with EIA/JESD 78A IC latch-up standard.

6.3.14

I/O current injection characteristics

As a general rule, current injection to the I/O pins, due to external voltage below VSS or

above VDD (for standard, 3 V-capable I/O pins) should be avoided during normal product

operation. However, to give an indication of the robustness of the microcontroller in cases

when abnormal injection accidentally happens, susceptibility tests are performed on a

sample basis during device characterization.

Functional susceptibility to I/O current injection

While a simple application is executed on the device, the device is stressed by injecting

current into the I/O pins programmed in floating input mode. While current is injected into

the I/O pin, one at a time, the device is checked for functional failures.

The failure is indicated by an out of range parameter: ADC error above a certain limit (higher

than 5 LSB TUE), out of conventional limits of induced leakage current on adjacent pins (out

of –5 µA/+0 µA range), or other functional failure (for example reset occurrence or oscillator

frequency deviation).

The test results are given in Table 65.

Table 64. Electrical sensitivities

Symbol

Parameter

Conditions

Class

Static latch-up class

TA = +105 °C conforming to JESD78A

II Level A

Table 65. I/O current injection susceptibility

Symbol

Description

Functional susceptibility

Unit

Negative

injection

Positive

injection

IINJ

Injected current on BOOT0

-0

Injected current on PF3, PC1, PC2, PA1, PA2, PA3,

PA4, PA5, PA6, PA7, PB0, PB1, PE8, PE9, PE10, PE11,

PE12, PE13, PE14, PE15, PB13, PB14, PB15, PD8,

PD9, PD10, PD11, PD12, PD13, PD14 pins with

induced leakage current on adjacent pins less than -

50 µA or more than +400 µA

-5

Injected current on PF2, PF4, PC0, PC1, PC2, PC3,

PA0, PA1, PA2, PA3, PA4, PA5, PA6, PA7, PC4, PC5,

PB2, PB11 with induced leakage current on other pins

from this group less than -50 µA or more than +400 µA

-5

STM32F303XD Datasheet(PDF) 117 Page - STMicroelectronics

STM32F303XD Datasheet(HTML) 117 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL