S29GL032A datasheet(47/88 Pages) SPANSION

47 / 88 page

January 28, 2005 S29GLxxxA_00_A2

S29GLxxxA MirrorBit™ Flash Family

Advance

Information

When the Embedded Program algorithm is complete, the device then returns to

the read mode and addresses are no longer latched. The system can determine

the status of the program operation by using DQ7 or DQ6. Refer to the Write Op-

eration Status section for information on these status bits. Any commands

written to the device during the Embedded Program Algorithm are ignored. Note

that the Secured Silicon Sector, autoselect, and CFI functions are unavailable

when a program operation is in progress. Note that a hardware reset immedi-

ately terminates the program operation. The program command sequence should

be reinitiated once the device has returned to the read mode, to ensure data

integrity.

Programming is allowed in any sequence of address locations and across sector

boundaries. Programming to the same word address multiple times without in-

tervening erases (incremental bit programming) requires a modified

programming method. For such application requirements, please contact your

local Spansion representative. Word programming is supported for backward

compatibility with existing Flash driver software and for occasional writing of in-

dividual words. Use of write buffer programming (see below) is strongly

recommended for general programming use when more than a few words are to

be programmed. The effective word programming time using write buffer pro-

gramming is approximately four times shorter than the single word programming

time.

Any bit in a word cannot be programmed from “0” back to a “1.” Attempt-

ing to do so may cause the device to set DQ5=1, or cause DQ7 and DQ6 status

bits to indicate the operation was successful. However, a succeeding read will

show that the data is still “0.” Only erase operations can convert a “0” to a “1.”

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to program words to the device

faster than using the standard program command sequence. The unlock bypass

command sequence is initiated by first writing two unlock cycles. This is followed

by a third write cycle containing the unlock bypass command, 20h. The device

then enters the unlock bypass mode. A two-cycle unlock bypass mode command

sequence is all that is required to program in this mode. The first cycle in this se-

quence contains the unlock bypass program command, A0h; the second cycle

contains the program address and data. Additional data is programmed in the

same manner. This mode dispenses with the initial two unlock cycles required in

the standard program command sequence, resulting in faster total programming

time.Table 25 and Table 26 show the requirements for the command sequence.

During the unlock bypass mode, only the Unlock Bypass Program and Unlock By-

pass Reset commands are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset command sequence. The first cycle

must contain the data 90h. The second cycle must contain the data 00h. The de-

vice then returns to the read mode.

Write Buffer Programming

Write Buffer Programming allows the system write to a maximum of 16 words/32

bytes in one programming operation. This results in faster effective programming

time than the standard programming algorithms. The Write Buffer Programming

command sequence is initiated by first writing two unlock cycles. This is followed

by a third write cycle containing the Write Buffer Load command written at the

Sector Address in which programming will occur. The fourth cycle writes the sec-

tor address and the number of word locations, minus one, to be programmed. For

S29GL032A Datasheet(PDF) 47 Page - SPANSION

S29GL032A Datasheet(HTML) 47 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

Datasheet Download

Link URL