Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

MPQ2420GF Datasheet(PDF) 13 Page - Monolithic Power Systems

Part # MPQ2420GF
Description  75V, 0.3A, Synchronous Step-Down Converter with Watchdog AEC-Q100 Qualified
PDF  22 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MPS [Monolithic Power Systems]
Direct Link  http://www.monolithicpower.com
Logo MPS - Monolithic Power Systems

MPQ2420GF Datasheet(HTML) 13 Page - Monolithic Power Systems

Back Button MPQ2420GF Datasheet HTML 9Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 10Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 11Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 12Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 13Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 14Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 15Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 16Page - Monolithic Power Systems MPQ2420GF Datasheet HTML 17Page - Monolithic Power Systems Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 22 page
background image
MPQ2420
―75V, 0.3A, SYNCHRONOUS STEP-DOWN CONVERTER WITH WATCHDOG
MPQ2420 Rev. 1.0
www.MonolithicPower.com
13
5/24/2016
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2016 MPS. All Rights Reserved.
Under-Voltage Lockout (UVLO)
Under-voltage lockout (UVLO) protects the chip
from operating below the operational supply
voltage range. The UVLO rising threshold is
about 4.2V while its falling threshold is about
3.75V.
Soft Start (SS)
The
MPQ2420
employs
a
soft-start
(SS)
mechanism to prevent the converter output
voltage from overshooting during start-up. When
the chip starts, the internal circuitry generates a
constant current to charge an external soft-start
capacitor. The SS voltage ramps up slowly from
0V at a slow pace set by the SS time. When VSS
is less than VREF, VSS overrides VREF, and the FB
comparator uses VSS as the reference instead of
VREF. When VSS is higher than VREF, VREF
resumes control.
VSS can be much smaller than VFB, but it can only
barely exceed VFB. If VFB drops, VSS tracks VFB.
This
function
prevents
an
output
voltage
overshoot during short-circuit recovery. When the
short circuit is removed, a new SS process
ramps up.
Thermal Shutdown
Thermal
shutdown
prevents
the
chip
from
operating at exceedingly high temperatures.
When the silicon die reaches temperatures that
exceed its upper threshold, the entire chip shuts
down. When the temperature falls below its lower
threshold, the chip is enabled again.
Floating Driver and Bootstrap Charging
An external bootstrap capacitor powers the
floating HS-FET driver. This floating driver has
its own UVLO protection. This
UVLO’s rising
threshold is about 2.4V with a hysteresis of about
300mV. During the UVLO, the SS voltage resets
to zero. When the UVLO is disabled, the
regulator follows the soft-start process.
The
dedicated
internal
bootstrap
regulator
charges and regulates the bootstrap capacitor to
about 5V. When the voltage difference between
BST and SW falls below its working parameters,
a PMOS pass transistor connected from VIN to
BST turns on to charge the bootstrap capacitor.
The current path runs from VIN to BST to SW.
The external circuit must have enough voltage
headroom to accommodate charging.
If VIN is sufficiently higher than SW, the bootstrap
capacitor charges. When the HS-FET is on, VIN is
about equal to SW, and the bootstrap capacitor
cannot charge. The optimal charging period
occurs when the LS-FET is on and VIN - VSW is at
its largest. VSW is equal to VOUT when there is no
current in the inductor. The difference between
VIN and VOUT charges the bootstrap capacitor.
If the internal circuit does not have sufficient
voltage
and
time
to
charge
the
bootstrap
capacitor, extra external circuitry can be used to
ensure that the bootstrap voltage operates in its
normal region.
Start-Up and Shutdown
If both VIN and VEN are higher than their
appropriate thresholds, the chip starts up. The
reference block starts first, generating stable
reference voltages and currents, and then the
internal regulator is enabled. The regulator
provides a stable supply for the remaining
circuitries.
If the internal supply rail is high, an internal timer
keeps the power MOSFET off for about 50µs to
clear any start-up glitches. When the soft-start
block is enabled, the SS output is held low and
ramps up slowly.
Three events can shut down the chip: VEN low,
VIN low, and thermal shutdown. During the
shutdown
procedure,
the
signaling
path
is
blocked first to avoid any fault triggering. The
internal supply rail is then pulled down. The
floating driver is not subject to this shutdown
command, but its charging path is disabled.
Power OK (POK)
POK is an open-drain power good output. A high
output indicates that VOUT is higher than 90% of
its nominal value. POK is pulled down in
shutdown mode.
Reference Voltage Output (VREF)
VREF has an output reference voltage of 1V. It has
up to 500µA of source current capability.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com