Rev 1.2

Page 10 of 10

www.sitime.com

Table 6. Revision History

Version

Release Date

Change Summary

0.1

12/15/2014

Advance Information

0.2

1/27/2015

Updated CSP dimension tolerance

Removed 2.0 mm x 1.6 mm package

Changed to 6.144 MHz as the reference frequency for jitter, IDD and other relevant parameters

Changed resume time (max) to 5 ms

Changed the parameter PSNR to Power Supply Noise Sensitivity and specified in RMS

0.3

03/31/2015

Changed VIL and VIH values in the EC table

Reduced standby time in the EC table

Revised phase jitter condition to include power supply noise sensitivity

Removed power supply noise spec

0.9

05/22/2015

Added typical values for active and standby current

Added current consumption for additional frequencies

Changed ±50 ppm option to Contact SiTime

Added manufacturing guideline

Other miscellaneous format and footnote changes

1.0

11/18/2015

Revised initial tolerance, current consumption, standby current, input high/low voltage, input pull-down impedance,

startup/resume time and RMS period/phase jitter in Table.1

Added performance plots

1.1

02/19/2016

Added 10 Standard frequencies to the ordering information

1.11

09/16/2016

Updated the table.5 list of standard frequencies

Added a graph of Idd vs Frequency without load to the performance plots section

1.2

09/28/2017

Added 2.25 to 3.63V supply voltage option

Updated logo and company address, other page layout changes

Added package dimension table to the dimensions and patterns section

SiTime Corporation, 5451 Patrick Henry Drive, Santa Clara, CA 95054, USA | Phone: +1-408-328-4400 | Fax: +1-408-328-4439

© SiTime Corporation 2014-2017. The information contained herein is subject to change at any time without notice. SiTime assumes no responsibility or liability for any loss, damage

or defect of a Product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a SiTime product, (ii) misuse or abuse including static discharge, neglect

or accident, (iii) unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by SiTime under its normal test conditions, or

(iv) improper installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress.

Disclaimer: SiTime makes no warranty of any kind, express or implied, with regard to this material, and specifically disclaims any and all express or implied warranties, either in fact or by

operation of law, statutory or otherwise, including the implied warranties of merchantability and fitness for use or a particular purpose, and any implied warranty arising from course of dealing or

usage of trade, as well as any common-law duties relating to accuracy or lack of negligence, with respect to this material, any SiTime product and any product documentation. Products sold by

SiTime are not suitable or intended to be used in a life support application or component, to operate nuclear facilities, or in other mission critical applications where human life may be involved

or at stake. All sales are made conditioned upon compliance with the critical uses policy set forth below.

CRITICAL USE EXCLUSION POLICY

BUYER AGREES NOT TO USE SITIME'S PRODUCTS FOR ANY APPLICATION OR IN ANY COMPONENTS USED IN LIFE SUPPORT DEVICES OR TO OPERATE NUCLEAR

FACILITIES OR FOR USE IN OTHER MISSION-CRITICAL APPLICATIONS OR COMPONENTS WHERE HUMAN LIFE OR PROPERTY MAY BE AT STAKE.

SiTime owns all rights, title and interest to the intellectual property related to SiTime's products, including any software, firmware, copyright, patent, or trademark. The sale of SiTime products does

not convey or imply any license under patent or other rights. SiTime retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale

of products or services by SiTime. Unless otherwise agreed to in writing by SiTime, any reproduction, modification, translation, compilation, or representation of this material shall be strictly

prohibited.