RXC101 datasheet(4/43 Pages) MURATA

4 / 43 page

www.RFM.com

Email: info@rfm.com

Page 4 of 43

©by RF Monolithics, Inc.

RXC101 - 4/8/08

1. Pin Description

Processor Mode

Name

Description

SDI

SPI Data In

SCK

SPI Data Clock

nCS

Chip Select Input

– Selects the chip for an SPI data transaction. The pin must be pulled ‘low’

for a 16-bit read or write function. See Figure 6 for timing specifications.

nFINT/SDO

FIFO Interrupt Output (active low)

– When the internal FIFO is enabled (Configuration

Bit [6]), this pin acts as a FIFO Fill interrupt indicating that the FIFO has filled to its

pre-programmed limit (FIFO Configuration Register, Bit [7..4]).

SPI Serial Data Out

– May be used to read out the Status Register contents.

nIRQ

Interrupt Request Output

– Any of the following events will generate an external interrupt:

-Wake-up timer timeout

-Low Battery Detect

-FIFO fill

-FIFO overflow

To determine the source of the interrupt, the processor may read the first four bits of the

Status Register

DATA/nFSEL

Data Output

– Received data can be taken from this pin when the FIFO is not used.

FIFO Select Input

– When the FIFO is used this pin selects the FIFO when data is to be read

out over the SDO pin.

DCLK/FCAP/

FINT

Data Recovery Clock Output

– Recovered Data clock Output (FIFO not used).

Filter Capacitor

– When the analog filter is used this pin is the connection for the RC

lowpass filter. The corner frequency should be set as close to the data rate as possible to

retain good sensitivity.

FIFO Interrupt Output (active high)

– Indicates when there are remaining bits in the FIFO to

be read. Set the FIFO Fill level to 1 in the FIFO Configuration Register.

ClkOut

Optional host processor Clock Output. Frequency programmable through the Battery Detect

Threshold and Clock Output Register.

Xtal/Ref

Xtal

- Connects to a 10MHz series crystal or an external oscillator reference. The circuit

contains an integrated load capacitor (See Configuration Register) in order to minimize the

external component count. The crystal is used as the reference for the PLL, which generates

the local oscillator frequency. The accuracy requirements for production tolerance,

temperature drift and aging can be determined from the maximum allowable local oscillator

frequency error. Whenever a low frequency error is essential for the application, it is possible

to “pull” the crystal to the accurate frequency by changing the load capacitor value.

Ext Ref

– An external reference, such as an oscillator, may be connected as a reference

source. Connect through a .01uF capacitor.

nRST

Reset Output

(active Low)

GND

System Ground

RF_P

RF Diff I/O

RF_N

RF Diff I/O

VDD

Supply Voltage

RSSIA

Analog RSSI Output

– This pin may be used as an input to an A/D for signal strength or may

be used as a baseband data output for OOK signaling. See Baseband Filter Register to

calculate the appropriate filter capacitor value.

DDET

Valid Data Detector Output

- (See Receiver Control Register for output definition)

1.1 Processor Mode Pin Configuration

SDI

SCK

nCS

SDO/FINT

IRQ

DATA/nFSEL

CR/FINT/FCAP

CLKOUT

DDET

RSSIA

VDD

RF_N

RF_P

GND

nRESET

Xtal/Ref

TOP VIEW

RXC101

RXC101 Datasheet(PDF) 4 Page - Murata Manufacturing Co., Ltd.

RXC101 Datasheet(HTML) 4 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

Datasheet Download

Link URL