Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

ISL5314EVAL2 Datasheet(PDF) 2 Page - Renesas Technology Corp

Part # ISL5314EVAL2
Description  Direct Digital Synthesizer
PDF  17 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  RENESAS [Renesas Technology Corp]
Direct Link  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

ISL5314EVAL2 Datasheet(HTML) 2 Page - Renesas Technology Corp

  ISL5314EVAL2 Datasheet HTML 1Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 2Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 3Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 4Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 5Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 6Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 7Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 8Page - Renesas Technology Corp ISL5314EVAL2 Datasheet HTML 9Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 2 / 17 page
background image
ISL5314
FN4901 Rev 3.00
Page 2 of 17
January 19, 2010
Pin Descriptions
PIN NO.
PIN NAME
TYPE
PIN DESCRIPTION
44-48, 1-3
C(7:0)
Input
8-bit processor input data bus. C7 is the MSB. Data is written to the control register selected on
A(3:0) on the rising edge of WR when WE is active.
42
WR
Input
Write clock for the processor interface. Parallel data is clocked into the chip on the rising edge of
WR.
40
WE
Input
Write enable. Active low. WE must be active when writing data to the chip.
35-38
A(3:0)
Input
Processor interface address bus. These pins select the destination register for data on the C(7:0)
bus. A3 is the MSB.
6
CLK
Clock
NCO and DAC clock. The phase accumulator and DAC output update on the rising edge of this
clock. CLK can be asynchronous to the WR clock.
8
RESET
Input
Reset. Active low. Resets control registers to their default states (see register description table)
and zeroes the feedback in the phase accumulator. UPDATE must be low for Reset to occur.
30
SCLK
Input
Serial clock. Polarity is programmable. See control word 12. May be asynchronous to CLK. If not
used, connect to DGND.
27
SDATA
Input
Serial data. See control word 12. If not used, connect to DGND.
32
SSYNC
Input
Serial sync. See control word 12. If not used, connect to DGND.
9UPDATE
Input
Active low. Updates the active control registers only. It has no effect on the ENOFR or PH(1:0)
pins. This pin is provided for updating an entire frequency word at once rather than byte by byte.
33, 34
PH(1:0)
Input
Phase offset bits. The phase of the output is shifted. If not used, these pins should be grounded.
00 – 0° reference
01 – 90° shift
10 – 180° shift
11 – 270° shift
4
ENOFR
Input
Enable offset frequency. Active high. When high, the offset frequency bus is enabled to the phase
accumulator. When low, the offset frequency bus is zeroed. This pin does not affect the contents
of the offset frequency registers. If not used, the pin should be grounded.
10
COMPOUT
Output
Comparator output.
11
REFLO
Input
Connect to analog ground to enable the DAC’s internal 1.2V reference or connect to AVDD to
disable the internal reference.
12
REFIO
Input
Reference voltage input for the DAC if internal reference is disabled. Recommend the use of a
0.1µF cap to ground from the REFIO pin when a DC reference voltage is used.
13
FSADJ
Full scale current adjust for the DAC. Use a resistor to ground (RSET) to adjust the full scale
output current. Full Scale Output Current = 32 x VFSADJ/RSET, where VFSADJ equals the
reference voltage.
14
COMP1
Noise reduction for the DAC. Connect a 0.1µF cap to AVDD plane.
19
COMP2
Noise reduction for the DAC. Connect a 0.1µF cap to AGND plane.
18
IOUTA
Output
DAC current output.
17
IOUTB
Output
DAC complementary current output.
20
AVDD
Power
Analog supply voltage.
15, 16, 21, 24
AGND
GND
Analog ground.
7, 26, 31, 43
DVDD
Power
Digital supply voltage.
5, 25, 28, 29, 41
DGND
GND
Digital ground.
22, 23
IN+, IN-
Input
Comparator inputs. To power down the comparator, connect both of these pins to the analog
power supply. This will conserve ~4mA of current.
39
NC
NC
No connect.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com