LM339, LM339A, LM239, LM239A, LM2901, M2901V, MC3302

http://onsemi.com

2

LM239A/339A

LM239/339

LM2901/2901V

MC3302

Characteristic

Symbol

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Unit

Input Offset Voltage (Note 4)

VIO

–

±1.0 ±2.0

–

±2.0 ±5.0

–

±2.0 ±7.0

–

±3.0 ±20

mVdc

Input Bias Current (Notes 4, 5)

IIB

–

25

250

–

25

250

–

25

250

–

25

500

nA

(Output in Analog Range)

Input Offset Current (Note 4)

IIO

–

±5.0 ±50

–

±5.0 ±50

–

±5.0 ±50

–

±3.0 ±100

nA

Input Common Mode Voltage

Range

VICMR

0

–

VCC

–1.5

0

–

VCC

–1.5

0

–

VCC

–1.5

0

–

VCC

–1.5

V

Supply Current

ICC

mA

RL = ∞ (For All Comparators)

–

0.8

2.0

–

0.8

2.0

–

0.8

2.0

–

0.8

2.0

RL = ∞, VCC = 30 Vdc

–

1.0

2.5

–

1.0

2.5

–

1.0

2.5

–

1.0

2.5

Voltage Gain

AVOL

50

200

–

50

200

–

25

100

–

25

100

–

V/mV

RL ≥ 15 kΩ, VCC = 15 Vdc

Large Signal Response Time

–

–

300

–

–

300

–

–

300

–

–

300

–

ns

VI = TTL Logic Swing,

Vref = 1.4 Vdc, VRL = 5.0 Vdc,

RL = 5.1 kΩ

Response Time (Note 6)

–

–

1.3

–

–

1.3

–

–

1.3

–

–

1.3

–

µs

VRL = 5.0 Vdc, RL = 5.1 kΩ

Output Sink Current

ISink

6.0

16

–

6.0

16

–

6.0

16

–

6.0

16

–

mA

VI (–) ≥ +1.0 Vdc, VI(+) = 0,

VO ≤ 1.5 Vdc

Saturation Voltage

Vsat

–

130

400

–

130

400

–

130

400

–

130

500

mV

VI(–) ≥ +1.0 Vdc, VI(+) = 0,

Isink ≤ 4.0 mA

Output Leakage Current

IOL

–

0.1

–

–

0.1

–

–

0.1

–

–

0.1

–

nA

VI(+) ≥ +1.0 Vdc, VI(–) = 0,

VO = +5.0 Vdc

LM239A/339A

LM239/339

LM2901/2901V

MC3302

Characteristic

Symbol

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Unit

Input Offset Voltage (Note 4)

VIO

–

–

±4.0

–

–

±9.0

–

–

±15

–

–

±40

mVdc

Input Bias Current (Notes 4, 5)

IIB

–

–

400

–

–

400

–

–

500

–

–

1000

nA

(Output in Analog Range)

Input Offset Current (Note 4)

IIO

–

–

±150

–

–

±150

–

–

±200

–

–

±300

nA

Input Common Mode Voltage

Range

VICMR

0

–

VCC

–2.0

0

–

VCC

–2.0

0

–

VCC

–2.0

0

–

VCC

–2.0

V

Saturation Voltage

Vsat

–

–

700

–

–

700

–

–

700

–

–

700

mV

VI(–) ≥ +1.0 Vdc, VI(+) = 0,

Isink ≤ 4.0 mA

Output Leakage Current

IOL

–

–

1.0

–

–

1.0

–

–

1.0

–

–

1.0

µA

VI(+) ≥ +1.0 Vdc, VI(–) = 0,

VO = 30 Vdc

Differential Input Voltage

VID

–

–

VCC

–

–

VCC

–

–

VCC

–

–

VCC

Vdc

All VI ≥ 0 Vdc

NOTES: 3. (LM239/239A) Tlow = –25°C, Thigh = +85°

(LM339/339A) Tlow = 0°C, Thigh = +70°C

(MC3302) Tlow = –40°C, Thigh = +85°C

(LM2901) Tlow = –40°C, Thigh = +105°

(LM2901V) Tlow = –40°C, Thigh = +125°C

4. At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 Ω 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range

(0 Vdc to VCC –1.5 Vdc).

5. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state.

6. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical.