LM3203 datasheet(4/15 Pages) NSC

4 / 15 page

Electrical Characteristics (Notes 2, 7) Limits in standard typeface are for T

A =TJ = 25˚C. Limits in boldface

type apply over the full operating ambient temperature range (−30˚C

≤ T

A =TJ

≤ +85˚C). Unless otherwise noted,

specifications apply to the LM3203 with: PV

IN =VDD = EN = 3.6V, BYP = 0V, VCON = 0.267V. (Continued)

Symbol

Parameter

Conditions

Min

Typ

Max

Units

Gain

CON to VOUT Gain

V/V

CON

CON Input Resistance

CON = 1.2V

Ω

System Characteristics The following spec table entries are guaranteed by design over ambient temperature

range if the component values in the typical application circuit are used. These parameters are not guaranteed by produc-

tion testing.

Symbol

Parameter

Conditions

Min

Typ

Max

Units

STARTUP Time for VOUT to rise

to 3.4V in PWM mode

IN = 4.2V, COUT = 4.7µF,

LOAD =10

Ω

L = 3.3uH (I

SAT > 0.94A)

EN = Low to High

µs

RESPONSE Time for VOUT to Rise

from 0.8V to 3.6V in

PWM Mode

IN = 4.2V, COUT = 4.7µF,

LOAD =10

Ω

L = 3.3uH (I

SAT > 0.94A)

µs

CON

CON Input

Capacitance

CON = 1V,

Test frequency = 100kHz

ON_BYP

Bypass FET Turn On

Time In Bypass Mode

IN = 3.6V, VCON = 0.267V,

OUT = 4.7µF, RLOAD =10

Ω

BYP = Low to High

µs

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of

the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the

Electrical Characteristics tables.

Note 2: All voltages are with respect to the potential at the GND pins.

Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150˚C (typ.) and disengages at TJ =

130˚C (typ.).

Note 4: The Human body model is a 100pF capacitor discharged through a 1.5k

Ω resistor into each pin. (MIL-STD-883 3015.7) . National Semiconductor

recommends that all integrated circuits be handled with appropriate precautions.

Note 5: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be

de-rated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125˚C), the maximum power

dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (θJA), as given by the

following equation: TA-MAX =TJ-MAX-OP –(θJA xPD-MAX).

Note 6: Junction-to-ambient thermal resistance (

θJA) is taken from thermal measurements, performed under the conditions and guidelines set forth in the JEDEC

standard JESD51-2. A 1" x 1", 4 layer, 1.5oz. Cu board was used for the measurements.

Note 7: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm.

Note 8: The LM3203 is designed for mobile phone applications where turn-on after power-up is controlled by the system controller and where requirements for a

small package size overrule increased die size for internal Under Voltage Lock-Out (UVLO) circuitry. Thus, it should be kept in shutdown by holding the EN pin low

until the input voltage exceeds 2.7V.

Note 9: Over-Voltage protection (OVP) threshold is the voltage above the nominal VOUT where the OVP comparator turns off the PFET switch while in PWM mode.

The OVP threshold will be the value of the threshold at the FB voltage times the resistor divider ratio. In the Figure 1, 100mV (typ.) x ((267K + 133K) ÷ 133K).

Note 10: Shutdown current includes leakage current of PFET and Bypass FET.

Note 11: Electrical Characteristic table reflects open loop data (FB=0V and current drawn from SW pin ramped up until cycle by cycle current limit is activated).

Refer to datasheet curves for closed loop data and its variation with regards to supply voltage and temperature. Closed loop current limit is the peak inductor current

measured in the application circuit by increasing output current until output voltage drops by 10%.

Note 12: Bypass FET current limit is defined as the load current at which the FB voltage is 1V lower than VIN.

LM3203 Datasheet(PDF) 4 Page - National Semiconductor (TI)

LM3203 Datasheet(HTML) 4 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Datasheet Download

Link URL