MODEL: 10EPF

http://www.m-system.co.jp/

10EPF SPECIFICATIONS

ES-0842 Rev.8 Page 1/3

High-density Signal Conditioners 10-RACK

POWER FACTOR TRANSDUCER

Functions & Features

• Providing a DC output signal in proportion to power factor

• DC output containing little ripple is ideal for computer

input

• Isolation up to 2000 V AC (input circuit)

Typical Applications

• Centralized monitoring and control of power management

system in a manufacturing facility or building

• Measuring power factor for a motor

MODEL: 10EPF-[1][2][3][4]-R[5]

ORDERING INFORMATION

• Code number: 10EPF-[1][2][3][4]-R[5]

Specify a code from below for each [1] through [5].

(e.g. 10EPF-11PA-R/Q)

• Specify the specification for option code /Q

(e.g. /C01)

[1] CONFIGURATION

1: 3-phase / 3-wire

4: 3-phase / 4-wire

[2] INPUT (balanced load)

1: 110 V / 5 A AC

2: 110 V / 1 A AC

3: 220 V / 1 A AC

4: 220 V / 5 A AC

5: 220 V / 380 V / 1 A AC (3-phase / 4-wire)

6: 220 V / 380 V / 5 A AC (3-phase / 4-wire)

7: 110 V / 190 V / 1 A AC (3-phase / 4-wire)

8: 110 V / 190 V / 5 A AC (3-phase / 4-wire)

(220 V in code 5 and 6, and 110 V in code 7 and 8

are phase voltage)

[3] OUTPUT SIGNAL POLARITY

P: Negative in lag, positive in lead

M: Negative in lead, positive in lag

[4] OUTPUT

Current

A: 4 – 20 mA DC (Load resistance 600 Ω max.)

B: 2 – 10 mA DC (Load resistance 1200 Ω max.)

C: 1 – 5 mA DC (Load resistance 2400 Ω max.)

D: 0 – 20 mA DC (Load resistance 600 Ω max.)

E: 0 – 16 mA DC (Load resistance 750 Ω max.)

F: 0 – 10 mA DC (Load resistance 1200 Ω max.)

G: 0 – 1 mA DC (Load resistance 12 kΩ max.)

GW: -1 – +1 mA DC (Load resistance 10 kΩ max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)

Voltage

1: 0 – 10 mV DC (Load resistance 10 kΩ min.)

2: 0 – 100 mV DC (Load resistance 100 kΩ min.)

3: 0 – 1 V DC (Load resistance 1000 Ω min.)

4: 0 – 10 V DC (Load resistance 10 kΩ min.)

5: 0 – 5 V DC (Load resistance 5000 Ω min.)

6: 1 – 5 V DC (Load resistance 5000 Ω min.)

1W: -10 – +10 mV DC (Load resistance 10 kΩ min.)

2W: -100 – +100 mV DC (Load resistance 100 kΩ min.)

3W: -1 – +1 V DC (Load resistance 1000 Ω min.)

4W: -10 – +10 V DC (Load resistance 10 kΩ min.)

5W: -5 – +5 V DC (Load resistance 5000 Ω min.)

0: Specify voltage (See OUTPUT SPECIFICATIONS)

POWER INPUT

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[5] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

GENERAL SPECIFICATIONS

Construction: Rack-mounted; terminal access via screw

terminals at the front and via card-edge connector at the

rear; terminal cover provided

Connection

Input: M3.5 screw terminals (torque 0.8 N·m)