MODEL: 10BX

http://www.m-system.co.jp/

10BX SPECIFICATIONS

ES-0891 Rev.12 Page 1/5

High-density Signal Conditioners 10-RACK

STANDARD RACK

Functions & Features

• Standard 19" rack for 10-RACK signal conditioners

• 4 – 16 modules mountable

• Line power access at the terminal card, supplied via the

rear rack bus

• Direct interface to various DCS with the rack side

connector

MODEL: 10BX–[1][2]

ORDERING INFORMATION

• Code number: 10BX-[1][2]

Specify a code from below for each [1] and [2].

(e.g. 10BX-1/W/Q)

• Specify the specification for option code /Q

(e.g. /C01)

[1] CAPACITY & TERMINAL CARD FUNCTION

1: 16 ch.; 24 V DC powered

2-K: 15 ch.; 85 – 132 V AC powered

2-L: 15 ch.; 170 – 264 V AC powered

3: 15 ch.; 24 V DC & 85 – 132 V AC powered

(two independent power sources)

4: 16 ch.; 24 V DC (Fujitsu FCN type I/O connector)

7: 16 ch.; 24 V DC (Yokogawa VMx / PM1 card use)

8: 16 ch.; 24 V DC (Omron 3G8B2-NA000 / NA001 use)

10: 16 ch.; 24 V DC (Nippon Shokubai DCS use)

11: 16 ch.; 24 V DC (Azbil J-HAM50 / J-HMM00 module use)

12: 16 ch.; 24 V DC (Azbil J-AOM10 module use)

13: 8 ch.; 24 V DC (Azbil J-PIM00 module use)

A: 4 ch.; 24 V DC powered

B: 4 ch.; 85 – 132 V AC powered

C: 9 ch.; 24 V DC powered

D-K: 8 ch.; 85 – 132 V AC powered

D-L: 8 ch.; 170 – 264 V AC powered

M-System guarantees the connecting section.

[2] OPTIONS (multiple selections)

Mounting Bracket

blank: Rack mounting, standard

/W: Surface mounting

Other Options

blank: none

/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

Power supply and signal conditioner side of the main PWB are not coated.

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

RELATED PRODUCTS

• Blank filler plate (model: P-101)

• Connector terminal block (model: CNT)

• Special cable with 40-pin connector (model: FCN)

GENERAL SPECIFICATIONS

Construction: Metal plates assembly

Coating: Zn-Cr (black), alumetized steel

Connection

Power input: M4 screw terminals (torque 0.8 N·m)

Screw terminal: Nickel-plated brass

Isolation: I/O connector to power to FG

INSTALLATION

Power consumption

•AC: 85 – 132 V or 170 – 264 V, 47 – 63 Hz, 130 VA

minimum

•DC: Operating voltage range 24 V DC ±10 %, 2.5 A

minimum (ripple 10 % p-p max.)

Operating temperature: -5 to +55°C (23 to 131°F) 0 to 50°C

(32 to 122°F) for AC power

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting

15, 16-position rack, 10BX-13: JIS or EIA standard rack or

surface

4, 8, 9-position rack: Angle bracket or surface

Weight

10BX-1, 4, 7, 8, 10, 11, 12, 13, D: 1.9 kg (4.2 lb)

10BX-2, 3: 2.3 kg (5.1 lb)

10BX-A: 1.1 kg (2.4 lb)

10BX-B: 1.3 kg (2.9 lb)

10BX-C: 1.5 kg (3.3 lb)