DWM1001 Datasheet

© Decawave Ltd 2017

Subject to change without notice

Version 1.5

Page 26

10.3 Innovation, Science and Economic Development Canada (ISED), formerly

Industry Canada (IC), Compliance Statements

This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISDE applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

The OEM integrator is still responsible for testing their end-product for any additional compliance requirements

required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

This Module is labelled with its own IC ID. If the IC ID Certification Number is not visible while installed inside

another device then the final end product should display a label on it referring to the enclosed module in a visible

area with the following:

“Contains Transmitter Module IC: 23794-DWM1001” OR “Contains IC: 23794-DWM1001”

Ce module est étiqueté avec son propre ID IC. Si le numéro de certification IC ID n'est pas visible lorsqu'il est

installé à l'intérieur d'un autre appareil, l'appareil doit afficher l'étiquette sur le module de référence ci-joint. Dans

ce cas, le produit final doit être étiqueté dans un endroit visible par le texte suivant :

“Contains Transmitter Module IC: 23794-DWM1001” OR “Contains IC: 23794-DWM1001”

10.4 Regulatory Module Integration Instructions

This module has been granted modular approval for portable applications. OEM integrators for host products may

use the module in their final products without additional FCC / ISED certification if they meet the following

conditions. Otherwise, additional FCC / ISED approvals must be obtained.

•

The host product with the module installed must be evaluated for simultaneous transmission

requirements.

•

The user’s manual for the host product must clearly indicate the operating requirements and conditions

that must be observed to ensure compliance with current FCC/ISED RF exposure guidelines.

•

A label must be affixed to the outside of the host product with the following statements:

This device contains FCC ID: 2AQ33-DWM1001

This equipment contains equipment certified under IC: 23794-DWM1001

The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for

unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.

If the final host / module combination is intended for use as a portable device (see classifications below) the host

manufacturer is responsible for separate evaluations/approvals for the SAR requirements from FCC Part 2.1093

and RSS-102.

10.5 Device Classifications

Since host devices vary widely with design features and configurations module integrators shall follow the

guidelines below regarding device classification and simultaneous transmission, and seek guidance from their

preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive

management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned

testing activities.

The module integrator must determine the minimum distance required between their host device and the user’s

body. The FCC provides device classification definitions to assist in making the correct determination. Note that

these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory

requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in

determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the

FCC.