| Electronic Components Datasheet Search |
|
AE-CAP1 Datasheet(PDF) 39 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
AE-CAP1 Datasheet(HTML) 39 Page - Renesas Technology Corp |
|
39 / 46 page ![]() Application Example for Capacitive Touch (AE-CAP1) 5. Circuitry R12UM0011EU0100 Rev.1.00 Page 39 of 46 May 8, 2017 Pin S1 Board Connection S3 Board Connection BWS Board Connection MC Board Connection SC Board Connection 34 P4_2/TS18 P2_6/TS1 W-11 RxC2 ST28 35 N.C. N.C. N.C. N.C. N.C. 36 P4_3/TS17 P2_4/TS0 W-10 RxC3 ST29 37 N.C. N.C. N.C. N.C. N.C. 38 N.C. N.C. N.C. N.C. N.C. 39 N.C. N.C. N.C. N.C. N.C. 40 N.C. N.C. N.C. N.C. N.C. Notes: 1. BWS Application Board B# are buttons, S-# are slider pads, W-# are wheel pattern pads. 2. MC Application Board TxR# are excitation signals from the Target Board to couple into # button row, RxC# are the coupled signal from each column through the excited buttons for detection by the Target Board. 3. SC Application Board – note that when the S1 Target Board is in use, there are two inoperable buttons at the top right corner of the button array, due to touch-sense signal count limitations, buttons ST24 and ST25. 5.10 USB device The USB Micro-B connection jack connects the MCU to an external USB Host, FS capable, and receives power from the host PC. Table 15 USB device connector USB device connector AE-CAP1-S1 AE-CAP1-S3 Pin Description Signal/Bus Signal/Bus 1 +5VDC, connected to +5VUSB, also includes a sense voltage 2/3 divider to allow MCU sensing +5VUSB P4_7/USB_VBUS = 2/3 VUSB +5VUSB P4_7/USB_VBUS = 2/3 VUSB 2 Data- USB_DM USB_DM 3 Data+ USB_DP USB_DP 4 USB ID, jack internal switch, cable inserted N.C. N.C. 5 Ground GND VSS 5.11 J-Link OB USB The USB Micro-B connection jack connects the J-Link MCU to an external USB Host, FS capable, allowing re-programming and debugging of the target MCU firmware. Power for the Target Boards is not received from this connector. Table 16 J-Link USB connector (J14) J-Link OB USB Connector AE-CAP1-S1 AE-CAP1-S3 Pin Description Signal/Bus Signal/Bus 1 +5VDC N.C. N.C. 2 Data- J-Link MCU USB0_DM J-Link MCU USB0_DM 3 Data+ J-Link MCU USB0_DP J-Link MCU USB0_DP 4 USB ID, jack internal switch, cable inserted N.C. N.C. 5 Ground GND GND |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |