Performance at Commonly Used Drive Currents

Table 3: Performance at Commonly Used Drive Currents

Part Number

CRI

Drive

Current1

(mA)

Typical V

f

T

sp = 25°C

(V)

Typical Power

T

sp = 25°C

(W)

Typical Pulsed

Flux2

T

sp = 25°C

(lm)

Typical

DC Flux3

T

sp = 85°C

(lm)

Typical

Efficacy

T

sp = 25°C

(lm/W)

BXEM-27C0000-0-000

70

30

5.5

0.2

28

24

171

60

5.7

0.3

55

47

159

100

6.0

0.6

87

74

145

150

6.25

0.9

123

102

131

200

6.5

1.3

156

124

119

240

6.7

1.6

179

138

111

BXEM-27E0000-0-000

80

30

5.5

0.2

27

24

163

60

5.7

0.3

52

46

152

100

6.0

0.6

82

72

138

150

6.25

0.9

117

99

125

200

6.5

1.3

148

121

114

240

6.7

1.6

170

134

106

BXEM-27G0000-0-000

90

30

5.5

0.2

22

20

136

60

5.7

0.3

43

39

127

100

6.0

0.6

69

60

116

150

6.25

0.9

98

83

105

200

6.5

1.3

124

101

95

240

6.7

1.6

142

112

88

BXEM-30C0000-0-000

70

30

5.5

0.2

29

25

175

60

5.7

0.3

56

49

163

100

6.0

0.6

89

76

149

150

6.25

0.9

126

105

134

200

6.5

1.3

159

127

122

240

6.7

1.6

183

141

114

BXEM-30E0000-0-000

80

30

5.5

0.2

28

25

171

60

5.7

0.3

55

49

159

100

6.0

0.6

87

76

145

150

6.25

0.9

123

105

131

200

6.5

1.3

156

127

119

240

6.7

1.6

179

141

111

BXEM-30G0000-0-000

90

30

5.5

0.2

23

21

143

60

5.7

0.3

46

41

134

100

6.0

0.6

73

64

122

150

6.25

0.9

103

88

110

200

6.5

1.3

130

107

100

240

6.7

1.6

150

118

93

SMD 3030 LEDs are tested to the specifications shown using the nominal drive currents in Table 1. SMD 3030 may also

be driven at other drive currents dependent on specific application design requirements. The performance at any drive

current can be derived from the current vs. voltage characteristics shown in Figure 2 and the relative luminous flux vs.

current characteristics shown in Figure 3. The performance at commonly used drive currents is summarized in Table 3.

5

Notes for Table 3:

1. Alternate drive currents in Table 3 are provided for reference only and are not a guarantee of performance.

2. Bridgelux maintains a ± 7.5% tolerance on flux measurements.

3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.