Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

SST26VF020A-80E/MF Datasheet(PDF) 8 Page - Microchip Technology

Part # SST26VF020A-80E/MF
Description  2.5V/3.0V 2-Mbit Serial Quad I/O™ (SQI™) Flash Memory
PDF  74 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MICROCHIP [Microchip Technology]
Direct Link  http://www.microchip.com
Logo MICROCHIP - Microchip Technology

SST26VF020A-80E/MF Datasheet(HTML) 8 Page - Microchip Technology

Back Button SST26VF020A-80E/MF Datasheet HTML 4Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 5Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 6Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 7Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 8Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 9Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 10Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 11Page - Microchip Technology SST26VF020A-80E/MF Datasheet HTML 12Page - Microchip Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 74 page
background image
SST26VF020A
DS20006279C-page 8
 2020-2021 Microchip Technology Inc. and its subsidiaries
4.5.1
HARDWARE RESET OPERATION
To configure the RESET#/HOLD#/SIO3 pin as a
RESET# pin, bit 6 of the Configuration register must be
set to ‘1’. The factory default setting of bit 6 is
‘0’-HOLD# pin enabled. This is a nonvolatile bit, so the
register value at power-up will be the value prior to
power-down. Driving the RESET# pin high puts the
device in normal operating mode. The RESET# pin
must be driven low for a minimum of TRST time to reset
the device. The SIO1 pin (SO) is in high-impedance
state while the device is in Reset. A successful Reset
operation will reset the protocol to SPI mode, STATUS
register bits will become as follows: BUSY = 0,
WEL = 0, BP0 = 1, BP1 = 1 and BPL = 0; reset the
burst length to 8 bytes. Reset during an active program
or erase operation aborts the operation and data of the
targeted address range may be corrupted or lost due to
the aborted erase or program operation.
4.5.2
SOFTWARE RESET OPERATION
The Reset operation requires the Reset Enable
command, 66H, followed by the Reset command, 99H.
Once the Reset Enable and Reset commands are
successfully executed, the device returns to normal
operation Read mode and then does the following:
resets the protocol to SPI mode, resets the burst length
to 8 bytes, STATUS register bits BUSY = 0, WEL = 0;
and clears bit 1 (IOC) in the Configuration register to its
default state.
Note:
Any command other than the Reset
command
after
the
Reset
Enable
command will disable the Reset Enable.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com