| Electronic Components Datasheet Search |
|
LX1691IPW Datasheet(PDF) 2 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
LX1691IPW Datasheet(HTML) 2 Page - Microsemi Corporation |
|
2 / 15 page ![]() Microsemi Integrated Products 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 2 Copyright © 2003 Rev. 1.0, 7/16/2004 LX1691 Enhanced Multi-Mode CCFL Controller PRODUCTION DATA SHEET TM ® ABSOLUTE MAXIMUM RATINGS Supply Voltage (VDDP) ..................................................................................................... 6V Digital Input (ENABLE)....................................................................... -0.3V to VDDP +0.5V Analog Inputs (I_SNS, OC_SNS, OV_SNS)clamped to +/- 10V. Max peak current +/-100mA Analog Inputs (BRITE_IN)................................................................... -0.3V to VDDP +0.5V DIM_MODE Input ................................................................................ -0.3V to VDDP +0.5V DD_CLK Digital Input ........................................................................ 0.3V to VDDP +0.5V Digital Output (AOUT, BOUT) .................................................................. -0.3V to VDDP +0.5V Analog Outputs (BRITE_R, I_R, EA_OUT,BRITE_OUT) ....................... -0.3V to VDDP +0.5V Operating Temperature Range ........................................................................ -55 to 125°C Maximum Junction Temperature ...............................................................................150°C Package Peak Temperature for Solder Reflow (40 Seconds Maximum Exposure) ......... 255°C (+5 -0) Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. PACKAGE PIN OUT V DDP OP_SNS VIN_SNS BRITE_IN B OUT A OUT V DDA I_SNS DIM_MODE GND DIM_CLK EA_OUT I_R ENABLE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 BRITE_OUT BRITE_R PW PACKAGE (Top View) Pb-free 100% Matte Tin Lead Finish TH ERMAL DATA PW Plastic TSSOP 16-Pin THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ JA 99°C/W Junction Temperature Calculation: TJ = TA + (PD x θJA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. FUNCTIONAL PIN DESCRIPTION PIN NAME DESCRIPTION GND Ground VDDP Voltage Input, 3.0 to 5.5V input range. VDDP is switched (see ENABLE) to remove power from chip. An LDO regulator follows the switch and generates VDDA (see VDDA). The output driver stages are powered directly from the VDDP input. Care must be taken in power distribution design to minimize transients and noise coupling from VDDP to the VDDA output. VDDA Analog VDDA Supply Output. This output pin is used to connect an external capacitor to stabilize and filter the on chip VDDA LDO regulator. The input of the LDO is the switched VDDP supply. LDO output is normally 3.0V and is used to drive all circuitry except the output buffers at AOUT and BOUT. Drop out voltage is typically 50mV (@ 25°C) at 5mA, the average internal load. This output can supply up to a 5 mA external load. The output capacitor recommended is <1000nF of the ceramic dielectric type. AOUT A buffer N-FET driver output. 10K internal pull down, ± 100 mA peak current with 3 VDC applied to VDDP pin. BOUT B buffer N-FET driver output. 10K internal pull down, ± 100 mA peak current with 3 VDC applied to VDDP pin. DD_CLK* Digital Dimming Clock / Dimming Polarity. An input pin that may be selected to control burst frequency for Digital Dimming. This input can be forced to VDDA or VSS or any clock signal up to 1MHz. This pin is also used to control the dimming polarity when operating in the internally clocked digital dimming mode*. If DIM_MODE is in the open condition (Analog Dimming Mode) the DD_CLK input is tied to VDDA or open (internal pull-up) to select conventional dimming polarity. It is tied to Ground for reverse polarity. Conventional polarity means that lamp brightness increases with increasing voltage on the BRITE_IN pin. Reverse polarity means that brightness decreases with increasing voltage. If DIM_MODE is open and a low frequency pulse is applied to DD_CLK, lamp current amplitude is directly proportional to the voltage at BRITE_IN, and its duty cycle follows the DD_CLK waveform, e.g., current flows when DD_CLK is high. In this mode pulse count should be greater than fault count.. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |