Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

RE46C195 Datasheet(PDF) 21 Page - Microchip Technology

Part # RE46C195
Description  CMOS Low-Voltage Photoelectric Smoke Detector ASIC with Interconnect and Timer Mode
PDF  39 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MICROCHIP [Microchip Technology]
Direct Link  http://www.microchip.com
Logo MICROCHIP - Microchip Technology

RE46C195 Datasheet(HTML) 21 Page - Microchip Technology

Back Button RE46C195 Datasheet HTML 17Page - Microchip Technology RE46C195 Datasheet HTML 18Page - Microchip Technology RE46C195 Datasheet HTML 19Page - Microchip Technology RE46C195 Datasheet HTML 20Page - Microchip Technology RE46C195 Datasheet HTML 21Page - Microchip Technology RE46C195 Datasheet HTML 22Page - Microchip Technology RE46C195 Datasheet HTML 23Page - Microchip Technology RE46C195 Datasheet HTML 24Page - Microchip Technology RE46C195 Datasheet HTML 25Page - Microchip Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 39 page
background image
 2021 Microchip Technology Inc.
DS20006503A-page 21
RE46C195
4.3
Smoke Calibration
A separate calibration mode is entered for each
measurement mode (Normal, Hysteresis, Hush, and
Chamber Test), so that independent limits can be set
for each. In all calibration modes, the integrator output
can be accessed at the GLED output.
The Gamp output voltage, which represents the smoke
detection level, can be accessed at the RLED output.
The SmkComp output voltage is the result of the
comparison of Gamp with the integrator output and can
be accessed at HB. The FEED input can be clocked to
step up the smoke detection level at RLED. Once the
desired smoke threshold is reached, the TEST input is
pulsed low-to-high to store the result.
The procedure is described in the following steps:
1.
Power up with the bias conditions shown in
Figure 4-1.
2.
Drive TEST2 input from VSS to VDD to enter
programming mode. TEST2 should remain at
VDD through Step 8 described below.
3.
Apply three clock pulses to TEST input to enter
T3 mode. This initiates the calibration mode for
normal limits setting. The integrator output
should appear at GLED and the smoke
detection level at RLED.
4.
At this point, clock FEED to increase the smoke
detection level as needed. Pulling IO high with
FEED at a high logic level will initiate an
integration. The integrator output signal should
appear at GLED. The sequence of incrementing
the limit, performing an integration and
monitoring the HB output for the resulting
comparison, can be repeated until the desired
threshold is reached. Once the desired smoke
threshold is reached, with FEED held low, the IO
input should be pulsed low-to-high to latch the
smoke detection level.
5.
Apply a fourth clock pulse to TEST input to enter
T4 mode. This initiates the calibration mode for
hysteresis limits. The sequence in Step 4 should
be repeated to set the hysteresis limit.
6.
Apply a clock pulse to TEST input again to enter
T5 mode and initiate calibration for hush limits.
Repeat Step 4 to set the hush limit.
7.
Apply clock pulse to TEST input a sixth time to
enter T6 mode and initiate calibration for
chamber test limits. Repeat Step 4 to set the
chamber test limit.
8.
After pulsing the IO input to latch the chamber
test limit, the IO must be pulsed low-to-high a
second time to store the limits in memory.
FIGURE 4-4:
Timing Diagram for Modes T3 to T6 Limits Setting.
GLED
IRED
RLED
HB
IO
TEST
FEED
TEST2
Mode T3
– T6 – Limits Setting
VSS
VSS
VBST
VSS
VBST
VSS
VSS
VSS
VBST
VDD
VSS
VBST
VSS
VDD
Min Tsetup2 = 2 µs
Min PW3 = 100 µs
Min Td2 = 10 µs
Min PW1 = 10 µs
Min T1 = 20 µs
Min PW4 = 2 ms
Min PW2 = 10 ms



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com