Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

ISL81485IUZ Datasheet(PDF) 8 Page - Renesas Technology Corp

Part # ISL81485IUZ
Description  5V, 30Mbps, RS-485/RS-422 Transceiver
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  RENESAS [Renesas Technology Corp]
Direct Link  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

ISL81485IUZ Datasheet(HTML) 8 Page - Renesas Technology Corp

Back Button ISL81485IUZ Datasheet HTML 4Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 5Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 6Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 7Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 8Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 9Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 10Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 11Page - Renesas Technology Corp ISL81485IUZ Datasheet HTML 12Page - Renesas Technology Corp  
Zoom Inzoom in Zoom Outzoom out
 8 / 12 page
background image
ISL81485
FN6061 Rev 1.00
Page 8 of 12
July 2004
The RS-485, RS-422 driver is a differential output device that
delivers at least 2V across a 54
 load (RS-485), and at least
2.5V across a 100
 load (RS-422) even with VCC = 4.5V. The
drivers feature low propagation delay skew to maximize bit
width, and to minimize EMI.
The driver is three-statable via the active high DE input.
Outputs of the driver are not slew rate limited, so faster output
transition times allow data rates of at least 30Mbps.
Data Rate, Cables, and Terminations
RS-485/RS-422 are intended for network lengths up to 4000’,
but the maximum system data rate decreases as the
transmission length increases. Devices operating at 30Mbps
usually are limited to lengths of a couple hundred feet, but the
larger differential output voltage of this transceiver allows that
distance to be pushed past 350’. Figure 7 illustrates the
30Mbps performance of the ISL81485 driving 350’ of CAT5
cable, terminated in 120
 at both the driver and receiver ends.
As shown, the differential signal (A-B) delivered to the receiver
inputs at the end of the cable is still greater than 1.5V (i.e., 7.5
times the required Rx sensitivity). Thus, even longer cables
can be driven if lower noise margins are acceptable.
Twisted pair is the cable of choice for RS-485, RS-422
networks. Twisted pair cables tend to pick up noise and other
electromagnetically induced voltages as common mode
signals, which are effectively rejected by the differential
receivers in these ICs.
Proper termination is imperative, when using a 30Mbps device,
to minimize reflections. In point-to-point, or point-to-multipoint
(single driver on bus) networks, the main cable should be
terminated in its characteristic impedance (typically 120
) at
the end farthest from the driver. In multi-receiver applications,
stubs connecting receivers to the main cable should be kept as
short as possible. Multipoint (multi-driver) systems require that
the main cable be terminated in its characteristic impedance at
both ends. Stubs connecting a transceiver to the main cable
should be kept as short as possible.
Built-In Driver Overload Protection
As stated previously, the RS-485 spec requires that drivers
survive worst case bus contentions undamaged. The
ISL81485 meets this requirement via driver output short circuit
current limits, and on-chip thermal shutdown circuitry.
The driver output stages incorporate short circuit current
limiting circuitry which ensures that the output current never
exceeds the RS-485 spec, even at the common mode voltage
range extremes.
In the event of a major short circuit condition, the device also
includes a thermal shutdown feature that disables the drivers
whenever the die temperature becomes excessive. This
eliminates the power dissipation, allowing the die to cool. The
drivers automatically reenable after the die temperature drops
about 15 degrees. If the contention persists, the thermal
shutdown/reenable cycle repeats until the fault is cleared.
Receivers stay operational during thermal shutdown.
Typical Performance Curves VCC = 5V, TA = 25oC; Unless Otherwise Specified
FIGURE 7. DRIVER AND RECEIVER WAVEFORMS DRIVING
350 FEET (107 METERS) OF CAT5 CABLE
(DOUBLE TERMINATED WITH 120
)
FIGURE 8. DRIVER OUTPUT CURRENT vs SHORT CIRCUIT
VOLTAGE
TIME (20ns/DIV)
-3
1.5
3
-1.5
0
0
5
0
5
DI = 30Mbps
RO
DRIVER+CABLE DELAY
(~490ns)
A - B
OUTPUT VOLTAGE (V)
-7 -6
-4
-2
0
2
4
6
8
10
12
-60
-40
-20
0
20
40
60
80
100
120
140
160
-80
-100
-120
Y OR Z = HIGH
-140
-160
Y OR Z = LOW
Y OR Z = HIGH



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com