MCP6071T-ESLASHOT datasheet(15/42 Pages) MICROCHIP

15 / 42 page

 2009-2021 Microchip Technology Inc. and its subsidiaries

DS20002142C-page 15

MCP6071/2/4

4.2

Rail-to-Rail Output

The output voltage range of the MCP6071/2/4 op amps

is VSS + 15 mV (minimum) and VDD – 15 mV

(maximum) when RL =10k is connected to VDD/2

and VDD = 6.0V. Refer to Figures 2-27 and 2-28 for

more information.

4.3

Capacitive Loads

Driving large capacitive loads can cause stability

problems for voltage feedback op amps. As the load

capacitance increases, the feedback loop’s phase

margin decreases and the closed-loop bandwidth is

reduced. This produces gain peaking in the frequency

response, with overshoot and ringing in the step

response. While a unity-gain buffer (G = +1) is the most

sensitive to capacitive loads, all gains show the same

general behavior.

When driving large capacitive loads with these op

amps (e.g., > 100 pF when G = +1), a small series

resistor at the output (RISO in Figure 4-4) improves the

feedback loop’s phase margin (stability) by making the

output load resistive at higher frequencies. The

bandwidth will be generally lower than the bandwidth

with no capacitance load.

FIGURE 4-4:

Output Resistor, RISO

Stabilizes Large Capacitive Loads.

Figure 4-5 gives recommended RISO values for

different capacitive loads and gains. The x-axis is the

normalized load capacitance (CL/GN), where GN is the

circuit's noise gain. For noninverting gains, GN and the

Signal Gain are equal. For inverting gains, GN is

1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V).

FIGURE 4-5:

Recommended RISO Values

for Capacitive Loads.

After selecting RISO for your circuit, double-check the

resulting frequency response peaking and step

response overshoot. Modify RISO’s value until the

response is reasonable. Bench evaluation and

simulations with the MCP6071/2/4 SPICE macro

model are very helpful.

4.4

Supply Bypass

With this family of operational amplifiers, the power

supply pin (VDD for single-supply) should have a local

bypass capacitor (i.e., 0.01 µF to 0.1 µF) within 2 mm

for good high frequency performance. It can use a bulk

capacitor (i.e., 1 µF or larger) within 100 mm to provide

large, slow currents. This bulk capacitor can be shared

with other analog parts.

4.5

Unused Op Amps

An unused op amp in a quad package (MCP6074)

should be configured as shown in Figure 4-6. These

circuits prevent the output from toggling and causing

crosstalk. Circuit A sets the op amp at its minimum

noise gain. The resistor divider produces any desired

reference voltage within the output voltage range of the

op amp; the op amp buffers that reference voltage.

Circuit B uses the minimum number of components

and operates as a comparator, but it may draw more

current.

FIGURE 4-6:

Unused Op Amps.

VIN

RISO

VOUT

MCP607X

–

100

1000

1.E-11

1.E-10

1.E-09

1.E-08

1.E-07

1.E-06

Normalized Load Capacitance; CL/GN (F)

GN:

1 V/V

2 V/V

 5 V/V

VDD = 6.0 V

RL = 10 kΩ

10p

100p

10n

0.1

1µ

VDD

¼ MCP6074 (A)

¼ MCP6074 (B)

VDD

VREF

VDD

R1 R2

--------------------



MCP6071T-E/OT Datasheet(PDF) 15 Page - Microchip Technology

MCP6071T-E/OT Datasheet(HTML) 15 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Datasheet Download

Link URL