| Electronic Components Datasheet Search |
|
TPA3002D2PHPR Datasheet(PDF) 32 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TPA3002D2PHPR Datasheet(HTML) 32 Page - Texas Instruments |
|
32 / 38 page ![]() TPA3002D2 SLOS402C − DECEMBER 2002 − REVISED JANUARY 2004 www.ti.com 32 C IN Audio Power Amplifier Generator Low-Pass RC Filter C IN R GEN R GEN R IN R IN V GEN R OUT R OUT Analyzer R ANA R ANA C ANA Low-Pass RC Filter R L C ANA Twisted-Pair Wire Evaluation Module Twisted-Pair Wire Figure 41. Differential Input—BTL output Measurement Circuit The generator should have balanced outputs and the signal should be balanced for best results. An unbalanced output can be used, but it may create a ground loop that will affect the measurement accuracy. The analyzer must also have balanced inputs for the system to be fully balanced, thereby cancelling out any common mode noise in the circuit and providing the most accurate measurement. The following general rules should be followed when connecting to APAs with differential inputs and BTL outputs: D Use a balanced source to supply the input signal. D Use an analyzer with balanced inputs. D Use twisted-pair wire for all connections. D Use shielding when the system environment is noisy. D Ensure the cables from the power supply to the APA, and from the APA to the load, can handle the large currents (see Table 3). Table 3 shows the recommended wire size for the power supply and load cables of the APA system. The real concern is the dc or ac power loss that occurs as the current flows through the cable. These recommendations are based on 12-inch long wire with a 20-kHz sine-wave signal at 25 °C. Table 3. Recommended Minimum Wire Size for Power Cables POUT (W) RL ( Ω) AWG SIZE DC POWER LOSS (MW) AC POWER LOSS (MW) 10 4 18 22 16 40 18 42 2 4 18 22 3.2 8.0 3.7 8.5 1 8 22 28 2.0 8.0 2.1 8.1 < 0.75 8 22 28 1.5 6.1 1.6 6.2 CLASS-D RC LOW-PASS FILTER An RC filter is used to reduce the square-wave output when the analyzer inputs cannot process the pulse-width modulated class-D output waveform. This filter has little effect on the measurement accuracy because the cutoff frequency is set above the audio band. The high frequency of the square wave has negligible impact on measurement accuracy because it is well above the audible frequency range and the speaker cone cannot respond at such a fast rate. The RC filter is not required when an LC low-pass filter is used, such as with the class-D APAs that employ the traditional modulation scheme (TPA032D0x, TPA005Dxx). The component values of the RC filter are selected using the equivalent output circuit as shown in Figure 42. RL is the load impedance that the APA is driving for the test. The analyzer input impedance specifications should be available and substituted for RANA and CANA. The filter components, RFILT and CFILT, can then be derived for the system. The filter should be grounded to the APA near the output ground pins or at the power supply ground pin to minimize ground loops. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |