PIC18F44J10-ESLASHML datasheet(223/358 Pages) MICROCHIP

223 / 358 page

Preliminary

DS39682C-page 221

PIC18F45J10 FAMILY

18.2

Comparator Operation

A single comparator is shown in Figure 18-2, along with

the relationship between the analog input levels and

the digital output. When the analog input at VIN+ is less

than the analog input VIN-, the output of the comparator

is a digital low level. When the analog input at VIN+ is

greater than the analog input VIN-, the output of the

comparator is a digital high level. The shaded areas of

the output of the comparator in Figure 18-2 represent

the uncertainty, due to input offsets and response time.

18.3

Comparator Reference

Depending on the comparator operating mode, either

an external or internal voltage reference may be used.

The analog signal present at VIN- is compared to the

signal at VIN+ and the digital output of the comparator

is adjusted accordingly (Figure 18-2).

FIGURE 18-2:

SINGLE COMPARATOR

18.3.1

EXTERNAL REFERENCE SIGNAL

When external voltage references are used, the

comparator module can be configured to have the com-

parators operate from the same or different reference

sources. However, threshold detector applications may

require the same reference. The reference signal must

be between VSS and VDD and can be applied to either

pin of the comparator(s).

18.3.2

INTERNAL REFERENCE SIGNAL

The comparator module also allows the selection of an

internally

generated

voltage

reference

from

the

comparator voltage reference module. This module is

described in more detail in Section 19.0 “Comparator

Voltage Reference Module”.

The internal reference is only available in the mode

where four inputs are multiplexed to two comparators

(CM2:CM0 = 110). In this mode, the internal voltage

reference is

applied

the

VIN+

both

comparators.

18.4

Comparator Response Time

Response time is the minimum time, after selecting a

new reference voltage or input source, before the

comparator output has a valid level. If the internal ref-

erence is changed, the maximum delay of the internal

voltage reference must be considered when using the

comparator outputs. Otherwise, the maximum delay of

the comparators should be used (see Section 23.0

“Electrical Characteristics”).

18.5

Comparator Outputs

The comparator outputs are read through the CMCON

outputs may also be directly output to the RB5 and RA5

I/O pins. When enabled, multiplexors in the output path

of the RB5 and RA5 pins will switch and the output of

each pin will be the unsynchronized output of the

comparator.

The

uncertainty

each

the

comparators is related to the input offset voltage and

the

response

time

given

the

specifications.

Figure 18-3 shows the comparator output block

diagram.

The TRISA bits will still function as an output enable/

disable for the RB5 and RA5 pins while in this mode.

The polarity of the comparator outputs can be changed

using the C2INV and C1INV bits (CMCON<5:4>).

–

VIN

Output

VIN-

VIN+

Note 1: When reading the Port register, all pins

configured as analog inputs will read as a

‘0’. Pins configured as digital inputs will

convert an analog input according to the

Schmitt Trigger input specification.

2: Analog levels on any pin defined as a

digital input may cause the input buffer to

consume more current than is specified.

PIC18F44J10-E/ML Datasheet(PDF) 223 Page - Microchip Technology

PIC18F44J10-E/ML Datasheet(HTML) 223 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL