PIC16F946-ESLASHMLQTP datasheet(204/330 Pages) MICROCHIP

204 / 330 page

PIC16F913/914/916/917/946

DS41250F-page 202

14.11 SSP I2C Operation

The SSP module in I2C mode, fully implements all slave

functions, except general call support, and provides

interrupts on Start and Stop bits in hardware to facilitate

firmware implementations of the master functions. The

SSP

module

implements

the

Standard

mode

specifications, as well as 7-bit and 10-bit addressing.

Two pins are used for data transfer. These are the

RC6/TX/CK/SCK/SCL/SEG9 pin, which is the clock

(SCL), and the RC7/RX/DT/SDI/SDA/SEG8 pin, which

is the data (SDA).

The SSP module functions are enabled by setting SSP

enable bit SSPEN (SSPCON<5>).

FIGURE 14-7:

SSP BLOCK DIAGRAM

(I2C™ MODE)

The SSP module has five registers for the I2C operation,

which are listed below.

• SSP Control register (SSPCON)

• SSP STATUS register (SSPSTAT)

• Serial Receive/Transmit Buffer (SSPBUF)

• SSP Shift register (SSPSR) – Not directly

accessible

• SSP Address register (SSPADD)

The SSPCON register allows control of the I2C

operation. Four mode selection bits (SSPCON<3:0>)

allow one of the following I2C modes to be selected:

•I2C Slave mode (7-bit address)

•I2C Slave mode (10-bit address)

•I2C Slave mode (7-bit address), with Start and

Stop bit interrupts enabled to support Firmware

Master mode

•I2C Slave mode (10-bit address), with Start and

Stop bit interrupts enabled to support Firmware

Master mode

•I2C Start and Stop bit interrupts enabled to

support Firmware Master mode; Slave is idle

Selection of any I2C mode with the SSPEN bit set

forces the SCL and SDA pins to be open drain,

provided these pins are programmed to inputs by

setting the appropriate TRISC bits. Pull-up resistors

must be provided externally to the SCL and SDA pins

for proper operation of the I2C module.

14.12 Slave Mode

In Slave mode, the SCL and SDA pins must be

configured as inputs (TRISC<7,6> are set). The SSP

module will override the input state with the output data

when required (slave-transmitter).

When an address is matched, or the data transfer after

an address match is received, the hardware

automatically will generate the Acknowledge (ACK)

pulse, and then load the SSPBUF register with the

received value currently in the SSPSR register.

There are certain conditions that will cause the SSP

module not to give this ACK pulse. They include (either

or both):

a) The Buffer Full bit BF of the SSPSTAT register

was set before the transfer was received.

b) The overflow bit SSPOV of the SSPCON

received.

In this case, the SSPSR register value is not loaded

into the SSPBUF, but bit SSPIF of the PIR1 register is

set. Table 14-3 shows the results of when a data

transfer byte is received, given the status of bits BF and

SSPOV. The shaded cells show the condition where

user software did not properly clear the overflow

condition. Flag bit BF is cleared by reading the

SSPBUF register, while bit SSPOV is cleared through

software.

The SCL clock input must have a minimum high and low

for proper operation. For high and low times of the I2C

specification, as well as the requirements of the SSP

module, see Section 19.0 “Electrical Specifications”.

Read

Write

SSPSR Reg

Match Detect

SSPADD Reg

Start and

Stop bit Detect

SSPBUF Reg

Internal

Data Bus

Addr Match

Set, Reset

S, P bits

(SSPSTAT Reg.)

Shift

Clock

MSb

LSb

SDI/

SCL

SCK/

SDA

PIC16F946-E/MLQTP Datasheet(PDF) 204 Page - Microchip Technology

PIC16F946-E/MLQTP Datasheet(HTML) 204 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL