PPC405EP datasheet(35/50 Pages) AMCC

35 / 50 page

PPC405EP – PowerPC 405EP Embedded Processor

Revision 1.07 – September 10, 2007

AMCC

Data Sheet

TDO

Test data out.

5V tolerant

3.3V LVTTL

TCK

JTAG test clock. The frequency of this input can range from DC to

25MHz.

5V tolerant

3.3V LVTTL

1, 4

TRST

JTAG reset. TRST must be low at power-on to initialize the JTAG

controller.

5V tolerant

3.3V LVTTL

System Interface

SysReset

Main system reset. External logic can drive this bidirectional pin low

(minimum of 16 cycles) to initiate a system reset. A system reset can

also be initiated by software. Implemented as an open-drain output

(two states; 0 or open circuit).

I/O

5V tolerant

3.3V LVTTL

1, 2

SysErr

Set to 1 when a Machine Check is generated.

5V tolerant

3.3V LVTTL

Halt

Halt from external debugger.

5V tolerant

3.3V LVTTL

1, 2

GPIO00:31

General Purpose I/O. All of the GPIO signals are multiplexed with

other signals.

I/O

5V tolerant

3.3V LVTTL

TestEn

Test Enable. Used only for manufacturing tests. Pull down for normal

operation.

1.8V CMOS

w/pull-down

SysClk

Main system clock input.

3.3V LVTTL

[RejectPkt0:1]

External request to reject a packet.

5V tolerant

3.3V LVTTL

AVDD

Clean voltage input for the PLL.

AGND

Clean Ground input for the PLL.

Trace Interface

[TS1E]

[TS2E]

Even Trace execution status. To access this function, software must

toggle a DCR bit

5V tolerant

3.3V LVTTL

[TS1O]

[TS2O]

Odd Trace execution status. To access this function, software must

toggle a DCR bit

5V tolerant

3.3V LVTTL

[TS3:6]

Trace status. To access this function, software must toggle a DCR bit

5V tolerant

3.3V LVTTL

[TrcClk]

Trace interface clock. Operates at half the CPU core frequency. To

access this function, software must toggle a DCR bit

5V tolerant

3.3V LVTTL

Power

GND

Ground

Note: K10-K14, L10-L14, M10-M14, N10-N14, and P10-P14 are also

thermal balls.

OVDD

Output driver voltage—3.3V.

Table 6. Signal Functional Description (Sheet 5 of 6)

Secondary multiplexed signals are shown in brackets.

Notes:

1. Receiver input has hysteresis.

2. Must pull up. See “Pull-Up and Pull-Down Resistors” on page 29 for recommended termination values.

3. Must pull down. See “Pull-Up and Pull-Down Resistors” on page 29 for recommended termination values.

4. If not used, must pull up.

5. If not used, must pull down.

6. Strapping input during reset; pull up or pull down as required.

7. Pull-up may be required. See “External Bus Control Signals” on page 30.

Signal Name

Description

I/O

Type

Notes

PPC405EP Datasheet(PDF) 35 Page - Applied Micro Circuits Corporation

PPC405EP Datasheet(HTML) 35 Page - Applied Micro Circuits Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

Datasheet Download

Link URL