TMP86PM29BUG datasheet(49/204 Pages) TOSHIBA

49 / 204 page

Page 35

TMP86PM29BUG

3. Interrupt Control Circuit

The TMP86PM29BUG has a total of 19 interrupt sources excluding reset, of which 3 source levels are multi-

plexed. Interrupts can be nested with priorities. Four of the internal interrupt sources are non-maskable while the rest

are maskable.

Interrupt sources are provided with interrupt latches (IL), which hold interrupt requests, and independent vectors.

The interrupt latch is set to “1” by the generation of its interrupt request which requests the CPU to accept its inter-

rupts. Interrupts are enabled or disabled by software using the interrupt master enable flag (IMF) and interrupt enable

flag (EF). If more than one interrupts are generated simultaneously, interrupts are accepted in order which is domi-

nated by hardware. However, there are no prioritized interrupt factors among non-maskable interrupts.

Note 1: The INTSEL register is used to select the interrupt source to be enabled for each multiplexed source level (see 3.3 Inter-

rupt Source Selector (INTSEL)).

Note 2: To use the address trap interrupt (INTATRAP), clear WDTCR1<ATOUT> to “0” (It is set for the “reset request” after reset is

cancelled). For details, see “Address Trap”.

Note 3: To use the watchdog timer interrupt (INTWDT), clear WDTCR1<WDTOUT> to "0" (It is set for the "Reset request" after

reset is released). For details, see "Watchdog Timer".

3.1

Interrupt latches (IL15 to IL2)

An interrupt latch is provided for each interrupt source, except for a software interrupt and an executed the unde-

fined instruction interrupt. When interrupt request is generated, the latch is set to “1”, and the CPU is requested to

accept the interrupt if its interrupt is enabled. The interrupt latch is cleared to "0" immediately after accepting inter-

rupt. All interrupt latches are initialized to “0” during reset.

The interrupt latches are located on address 003CH and 003DH in SFR area. Each latch can be cleared to "0" indi-

vidually by instruction. However, IL2 and IL3 should not be cleared to "0" by software. For clearing the interrupt

latch, load instruction should be used and then IL2 and IL3 should be set to "1". If the read-modify-write instructions

such as bit manipulation or operation instructions are used, interrupt request would be cleared inadequately if inter-

rupt is requested while such instructions are executed.

Interrupt Factors

Enable Condition

Interrupt

Latch

Vector

Address

Priority

Internal/External

(Reset)

Non-maskable

–

FFFE

Internal

INTSWI (Software interrupt)

Non-maskable

–

FFFC

Internal

INTUNDEF (Executed the undefined instruction

interrupt)

Non-maskable

–

FFFC

Internal

INTATRAP (Address trap interrupt)

Non-maskable

IL2

FFFA

Internal

INTWDT (Watchdog timer interrupt)

Non-maskable

IL3

FFF8

External

INT0

IMF• EF4 = 1, INT0EN = 1

IL4

FFF6

External

INT1

IMF• EF5 = 1

IL5

FFF4

Internal

INTTBT

IMF• EF6 = 1

IL6

FFF2

External

INT2

IMF• EF7 = 1

IL7

FFF0

Internal

INTTC

IMF• EF8 = 1

IL8

FFEE

Internal

INTRXD

IMF• EF9 = 1, IL9ER = 0

IL9

FFEC

Internal

INTSIO

IMF• EF9 = 1, IL9ER = 1

Internal

INTTXD

IMF• EF10 = 1

IL10

FFEA

Internal

INTTC4

IMF• EF11 = 1

IL11

FFE8

Internal

INTTC6

IMF• EF12 = 1

IL12

FFE6

Internal

INTADC

IMF• EF13 = 1

IL13

FFE4

External

INT3

IMF• EF14 = 1, IL14ER = 0

IL14

FFE2

Internal

INTTC3

IMF• EF14 = 1, IL14ER = 1

External

INT5

IMF• EF15 = 1, IL15ER = 0

IL15

FFE0

Internal

INTTC5

IMF• EF15 = 1, IL15ER = 1

TMP86PM29BUG Datasheet(PDF) 49 Page - Toshiba Semiconductor

TMP86PM29BUG Datasheet(HTML) 49 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL