ISL71841SEH

FN8735 Rev. 8.00

Page 27 of 30

Aug 10, 2023

Revision History The revision history provided is for informational purposes only and is believed to beaccurate, butnot warranted.

Please visit our website to make sure you have the latest revision.

DATE

REVISION

CHANGE

Aug 10, 2023

8.00

Removed Related Literature section.

Updated Ordering Information table and notes.

In ABS MAX RATINGS Section on page 5 changed Digital Input Voltage Range (EN, Ax) from GND to V+, to

GND - 0.3V to +16.5V.

Updates to the Electrical Specifications (±15V) table are as follows:

• On page 5, for parameters Channel On-Resistance, rON Match Between Channels, and ON-Resistance

Flatness, added VEN = 0V to the Test Conditions.

• On page 6, for parameter Switch Off Leakage with Device Powered OFF changed it to Switch Off Leakage

with Device Powered OPEN.

• On page 6, added new parameter Switch On Leakage Current into the Drain (Overvoltage) specification.

• On page 6, for parameter Switch On Leakage Current into the Source (Overvoltage), updated the limits

values and units to µA.

• On page 6, for parameter Switch Off Leakage Current into the Source (Overvoltage), added a new

TA = -55°C” specification.

• On page 7, for parameter Switch On Leakage Current into the Source/Drain, added VEN = 0V to the Test

Conditions.

• Changed the I+, I- Quiescent & Standby Supply Current parameters to VREF = 5.5V, VIN = 0V, VA = 0.8V.

• Changed parameter nomenclature for Supply Current Into VREF to Quiescent Supply Current Into VREF.

• Added new specification parameter Standby Current Into VREF.

Updates to the Electrical Specifications (±12V) table on page 8 are as follows:

• For parameters Channel On-Resistance, rON Match Between Channels, and ON-Resistance Flatness,

added VEN = 0V to the Test Conditions.

• Changed the I+, I- Quiescent & Standby Supply Current parameters to VREF = 5.5V, VIN = 0V, VA = 0.8V.

• Changed parameter nomenclature for Supply Current Into VREF to Quiescent Supply Current Into VREF.

• Added new specification parameter Standby Current Into VREF.

Feb 23, 2018

7.00

Added “Considerations for Redundant Applications” on page 24.

Removed About Intersil and updated disclaimer.

Nov 30, 2017

6.00

Added ESD circuit images in Figure 3 on page 4.

Jun 22, 2017

5.00

Ordering Information table on page 3, added Notes 5 and 6.

In “Pin Descriptions” on page 4, added pin 28 to NC for the CLCC package.

Jun 3, 2016

4.00

Updated Ordering information table on page 3 by updating first column and updating Note 4.

Updated bolding in Electrical Specification table and added test conditions to the Break-Before-Make Delay,

Enable Turn-On Time and Disable Turn-Off Time specifications.

Changed from “VS” to “V±” in the titles of the Typical Performance, Post High and Post Low Dose Rate

Radiation Characteristics curve tables.

Changed units from mA to µA for Figures 32, 33, 34, 44, 45, 46, 56, 57, 58, 68, 69, 70.

Apr 15, 2016

3.00

Added ISL71841SEHVL and ISL71841SEHL/PROTO details to the Ordering Information table on page 3 and

added the applicable packaging information throughout datasheet.

Updated the heading for the Low Dose Rate Radiation Characteristics (Vs = ±15V) table on page 20 in third

sentence changed from “high” to “low”.

Updated the heading for the Low Dose Rate Radiation Characteristics (Vs = ±12V) table on page 22 in third

sentence changed from “high” to “low”.

Dec 11, 2015

2.00

Updated Y-axis labels on Figures 32 through 79.

Updated crosstalk and off Isolation MIN in Electrical Spec table on page 8 from -75 to 75 (off isolation) and

-47 to 47 (crosstalk).

Changed all instances of VDD to V+ and VSS to V-.