ST10F272E datasheet(12/181 Pages) STMICROELECTRONICS

12 / 181 page

Introduction

ST10F272B/ST10F272E

12/181

A second PWM mapped on the XBUS is added (PWM of ST10F269 becomes here PWM0,

while the new one is referred as XPWM or simply as PWM1). Note that some restrictions

and functional differences due to the XBUS peculiarities are present between the classic

PWM, and the new XPWM.

An I2C interface on the XBUS is added (see X-I2C or simply I2C interface).

CLKOUT function can output either the CPU clock (like in ST10F269) or a software

programmable prescaled value of the CPU clock.

On-chip RAM memory has been increased (Flash size remained the same).

PLL multiplication factors have been adapted to new frequency range.

A/D Converter is not fully compatible versus ST10F269 (timing and programming model).

Formula for the convertion time is still valid, while the sampling phase programming model is

different.

Besides, additional 8 channels are available on P1L pins as alternate function: the accuracy

reachable with these extra channels is reduced with respect to the standard Port5 channels.

External Memory bus is affected by limitations on maximum speed and maximum

capacitance load: ST10F272 is not able to address an external memory at 64MHz with 0

wait states.

XPERCON register bit mapping modified according to new peripherals implementation (not

fully compatible with ST10F269).

Bondout chip for emulation (ST10R201) cannot achieve more than 50MHz at room

temperature (so no real time emulation possible at maximum speed).

Input section characteristics are different. The threshold programmability is extended to all

port pins (additional XPICON register); it is possible to select standard TTL (with up to

400mV of hysteresis) and standard CMOS (with up to 750mV of hysteresis).

Output transition is not programmable.

CAN module is enhanced: ST10F272 implements two C-CAN modules, so the programming

model is slightly different. Besides, the possibility to map in parallel the two CAN modules is

added (on P4.5/P4.6).

On-chip main oscillator input frequency range has been reshaped, reducing it from 1-25MHz

down to 4-8MHz. This is a low power oscillator amplifier, that allows a power consumption

reduction when Real Time Clock is running in Power Down mode, using as reference the on-

chip main oscillator clock. When this on-chip amplifier is used as reference for Real Time

Clock module, the Power-down consumption is dominated by the consumption of the

oscillator amplifier itself.

A second on-chip oscillator amplifier circuit (32kHz) is implemented for low power modes: it

can be used to provide the reference to the Real Time Clock counter (either in Power Down

or Stand-by mode). Pin XTAL3 and XTAL4 replace a couple of VDD/VSS pins of ST10F269.

Possibility to re-program internal XBUS chip select window characteristics (XRAM2 window)

is added.

ST10F272E Datasheet(PDF) 12 Page - STMicroelectronics

ST10F272E Datasheet(HTML) 12 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL