STM32F071C8H6 datasheet(22/121 Pages) STMICROELECTRONICS

22 / 121 page

Functional overview

STM32F071CB STM32F071RB STM32F071VB STM32F071V8

22/121

DocID025451 Rev 3

3.14.1

Advanced-control timer (TIM1)

The advanced-control timer (TIM1) can be seen as a three-phase PWM multiplexed on six

channels. It has complementary PWM outputs with programmable inserted dead times. It

can also be seen as a complete general-purpose timer. The four independent channels can

be used for:

•

input capture

•

output compare

•

PWM generation (edge or center-aligned modes)

•

one-pulse mode output

If configured as a standard 16-bit timer, it has the same features as the TIMx timer. If

configured as the 16-bit PWM generator, it has full modulation capability (0-100%).

The counter can be frozen in debug mode.

Many features are shared with those of the standard timers which have the same

architecture. The advanced control timer can therefore work together with the other timers

via the Timer Link feature for synchronization or event chaining.

3.14.2

General-purpose timers (TIM2, 3, 14, 15, 16, 17)

There are six synchronizable general-purpose timers embedded in the

STM32F071CB/RB/VB/V8 devices (see Table 6 for differences). Each general-purpose

timer can be used to generate PWM outputs, or as simple time base.

TIM2, TIM3

STM32F071CB/RB/VB/V8 devices feature two synchronizable 4-channel general-purpose

timers. TIM2 is based on a 32-bit auto-reload up/downcounter and a 16-bit prescaler. TIM3

is based on a 16-bit auto-reload up/downcounter and a 16-bit prescaler. They feature 4

independent channels each for input capture/output compare, PWM or one-pulse mode

output. This gives up to 12 input captures/output compares/PWMs on the largest packages.

The TIM2 and TIM3 general-purpose timers can work together or with the TIM1 advanced-

control timer via the Timer Link feature for synchronization or event chaining.

TIM2 and TIM3 both have independent DMA request generation.

These timers are capable of handling quadrature (incremental) encoder signals and the

digital outputs from 1 to 3 hall-effect sensors.

Their counters can be frozen in debug mode.

TIM14

This timer is based on a 16-bit auto-reload upcounter and a 16-bit prescaler.

TIM14 features one single channel for input capture/output compare, PWM or one-pulse

mode output.

Its counter can be frozen in debug mode.

TIM15, TIM16 and TIM17

These timers are based on a 16-bit auto-reload upcounter and a 16-bit prescaler.

STM32F071C8H6 Datasheet(PDF) 22 Page - STMicroelectronics

STM32F071C8H6 Datasheet(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL