| Electronic Components Datasheet Search |
|
ADC08060 Datasheet(PDF) 18 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
ADC08060 Datasheet(HTML) 18 Page - Texas Instruments |
|
18 / 32 page ![]() 22 + - 200 12 240 47 100 10 pF Signal Input 8 11 AGND ADC08060 D7 13 D6 14 D5 15 D0 22 D1 21 D2 20 D3 19 D4 16 6 3 7 10 VRT 5 0.1 PF 10 PF + 12 4 18 0.1 PF 10 PF DR VD VA Choke 1 VRB 24 CLK 9 23 PD +3V LMH6702 2 17 DR GND +5V -5V 0.1 PF 0.1 PF 10 Gain Adjust 4.7k 1k 1k 0.33 PF +3V * * Offset Adjust * *URXQG FRQQHFWLRQV PDUNHG ZLWK ³*´ should enter the ground plane at a common point VIN 7 VIN GND VRM ADC08060 SNAS120H – OCTOBER 2000 – REVISED MARCH 2013 www.ti.com The input amplifier should incorporate some gain for best performance (see text). Figure 32. The RC at the amplifier output filters the clock rate energy that comes out of the analog input due to the input sampling circuit. The optimum time constant for this circuit depends not only upon the amplifier and ADC, but also on the circuit layout and board material. A resistor value should be chosen between 18 Ω and 47Ω and the capacitor value chose according to the formula (5) This will provide optimum SNR performance. Best THD performance is realized when the capacitor and resistor values are both zero. To optimize SINAD, reduce the capacitor or resistor value until SINAD performance is optimized. That is, until SNR = −THD. This value will usually be in the range of 40% to 65% of the value calculated with the above formula. An accurate calculation is not possible because of the board material and layout dependence. The above is intended for oversampling or Nyquist applications. There should be no resistor or capacitor between the ADC input and any amplifier for undersampling applications. The circuit of Figure 32 has both gain and offset adjustments. If you eliminate these adjustments normal circuit tolerances may cause signal clipping unless care is exercised in the worst case analysis of component tolerances and the input signal excursion is appropriately limited to account for the worst case conditions. Of course, this means that the designer will not be able to depend upon getting a full scale output with maximum signal input. POWER SUPPLY CONSIDERATIONS A/D converters draw sufficient transient current to corrupt their own power supplies if not adequately bypassed. A 10 µF tantalum or aluminum electrolytic capacitor should be placed within an inch (2.5 cm) of the A/D power pins, with a 0.1 µF ceramic chip capacitor placed within one centimeter of the converter's power supply pins. Leadless chip capacitors are preferred because they have low lead inductance. 18 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: ADC08060 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |