KNS Series Datasheet

1

2

Measuring length L2: Resistance value is measured over the centered length L2 on terminals free of oxide and contaminations.

Differing conditions require adequate corrections (Rterminal = 0,4 [mΩ/cm]).

Type

KNS100

KNS150

KNS200

KNS250

KNS300

Historical Part Number

RADIAL

KN350 – 009

KN351 – 010

KN351 – 009

KN352 – 009

KN352 – 010

KN352 – 011

KN353 – 009

KN353 – 010

KN353 – 011

AXIAL

KN350 – 0

----------

KN351 – 0

KN352 – 0

----------

Derating Linear

[ºC]

70…300 (0W)

Climatic Category

55/200/56

Failure Rate

(Total

, ϑ

0 ,

max, 60[%] cont. lev.)

[10-9 h-1]

appr. 100 depends on value

Endurance

IEC60115-1 clause 4.25

(P70, @ 70[°C], 1000[h])

±[%]

3,0

Resistance to Soldering Heat

IEC60115-1 clause 4.18

(260±5[°C], 3,5±1[s])

±[%]

0,25

Damp Heat, Steady State

IEC60115-1 clause 4.24 ; IEC60068-2-78

(40[°C], 93[% r.h.], 56[d])

±[%]

0,5

1,5

0,5

1,5

Rapid change of temperature

IEC60115-1 clause 4.19 and IEC60068-2-14

(30 [min] -55 [ºC] and 30 [min] +125 [ºC])

±[%]

2,0

1,0

2,0

1,0

Biased Humidity

MIL-STD-202 Method 103

(85[ºC], 85[%RH] 1.000[h])

±[%]

1,0

2,5

1,0

2,5

Vibrations

Mil-STD-202 Method 204

(10 to 2000 [Hz], 5 [G] for 20 [min], 12 cycles, each of 3 orientation

±[%]

4,5

9,0

4,5

9,0

Mechanical Shock

Mil-STD-202 Method 213

(Method C, peak value 100 [G], Half sine)

±[%]

2,0

3,0

2,0

3,0

ESD

IEC60115-1 Clause 4.38, AEC-Q200-002

Direct contact, 2discharges, Cs = 150 [pf] , Rd = 2000 [Ω], V = 2[KV] (time/sec)

±[%]

2,0

1,5

2,0

1,5

Terminal Strength

±[%]

0,5

Terminal Tensile Strength

[N]

≥ 25

Solderability

IEC60068-2-20

(245±5[ºC] 3±0,5[s])

Solder bath method (> 95% coverage)

Marking

IEC60062

Value imprinted

Type

[Forming

Type]

Historical

P/N:

L1

L2

KNS100

[AX]

KN350 - 0

12,0 … 14,5

40

KNS200

KN351 - 0

17,5 … 21,5

45

KNS250

KN352 - 0

29,0 … 34,0

60

Axial Version: