| Electronic Components Datasheet Search |
|
SPC570S40E3 Datasheet(PDF) 48 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPC570S40E3 Datasheet(HTML) 48 Page - STMicroelectronics |
|
48 / 75 page ![]() Electrical characteristics SPC570S40Ex, SPC570S50Ex 48/75 DocID024492 Rev 7 Figure 8. Crystal/Resonator Connections VEXTAL CC D Oscillation Amplitude on the EXTAL pin after startup(9) TJ = –40°C to 150°C 0.5 1.6 V VHYS CC D Comparator Hysteresis TJ =150 °C 0.1 1.0 V IXTAL CC D XTAL current(10) TJ =150 °C — 14 mA 1. All oscillator specifications are valid for VDD_HV_IO =3.0 V–5.5V. 2. The range is selectable by UTEST miscellaneous DCF clients XOSC_LF_EN and XOSC_EN_40 MHZ. 3. This value is determined by the crystal manufacturer and board design. 4. Proper PC board layout procedures must be followed to achieve specifications. 5. Crystal recovery time is the time for the oscillator to settle to the correct frequency after adjustment of the integrated load capacitor value. 6. This parameter is guaranteed by design rather than 100% tested. 7. Applies to an external clock input and not to crystal mode. 8. See crystal manufacturer’s specification for recommended load capacitor (CL) values.The external oscillator requires external load capacitors when operating from 8 MHz to 16 MHz. Account for on-chip stray capacitance (CS_EXTAL/CS_XTAL) and PCB capacitance when selecting a load capacitor value. When operating at 20 MHz/40 MHz, the integrated load capacitor value is selected via S/W to match the crystal manufacturer’s specification, while accounting for on-chip and PCB capacitance. 9. Amplitude on the EXTAL pin after startup is determined by the ALC block, i.e., the Automatic Level Control Circuit. The function of the ALC is to provide high drive current during oscillator startup, but reduce current after oscillation in order to reduce power, distortion, and RFI, and to avoid over-driving the crystal. The operating point of the ALC is dependent on the crystal value and loading conditions. 10. IXTAL is the oscillator bias current out of the XTAL pin with both EXTAL and XTAL pins grounded. This is the maximum current during startup of the oscillator. The current after oscillation is typically in the 2-3 mA range and is dependent on the load and series resistance of the crystal. Test circuit is shown in Figure 9. The ALC block is the Automatic Level Control Circuit. The function of the ALC is to provide high drive current during oscillator startup, but reduce current after oscillation in order to reduce power, distortion, and RFI, and to avoid overdriving the crystal. Table 29. External Oscillator electrical specifications(1) (continued) Symbol C Parameter Conditions Value Unit Min Max Crystal or Resonator EXTAL XTAL On chip Off chip Cy Cx vsssyn 8-40 MHz EXTERNAL OSCILLATOR (XOSC) DRIVER |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |