| Electronic Components Datasheet Search |
|
SPC574K72E7 Datasheet(PDF) 31 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
SPC574K72E7 Datasheet(HTML) 31 Page - STMicroelectronics |
|
31 / 160 page ![]() DocID023601 Rev 6 31/160 SPC574Kx Electrical characteristics 159 VSS_HV_ADR SR P SD ADC ground reference voltage —VSS_HV_ADV V VSS_HV_ADR_D – VSS_HV_ADV SR D VSS_HV_ADR_D differential voltage — –25 — 25 mV VDD_HV_ADR_S(12) SR P SARADC reference — 4.5 — 5.5 V C4.0 5.9 C2.0 4.0 VDD_HV_ADR_S – VDD_HV_ADV SR D SARADC reference differential voltage —— — 25 mV VSS_HV_ADR_S – VSS_HV_ADV SR D VSS_HV_ADR_S differential voltage — –25 — 25 mV VSS_HV_ADV – VSS SR D VSS_HV_ADV differential voltage — –25 — 25 mV VRAMP_HV SR D Slew rate on HV power supply pins —— — 100 V/ms VIN SR C I/O input voltage range —0 — 5.5 V Injection current IIC SR T DC injection current (per pin)(13),(14),(15) Digital pins and analog pins –3.0 — 3.0 mA IMAXSEG SR D Maximum current per power segment(16) — –80 — 80 mA 1. The ranges in this table are design targets and actual data may vary in the given range. 2. Maximum operating frequency is applicable to the computational cores and platform for the device. See the Clocking chapter in the SPC574Kxx Microcontroller Reference Manual for more information on the clock limitations for the various IP blocks on the device. 3. Core voltage as measured on device pin to guarantee published silicon performance. 4. During power ramp, voltage measured on silicon might be lower. Maximum performance is not guaranteed, but correct silicon operation is guaranteed. Refer to the Power Management and Reset Generation Module chapters in the SPC574Kxx Microcontroller Reference Manual for further information. 5. Maximum voltage is not permitted for entire product life. See Table 7: Absolute maximum ratings. 6. When internal LVD/HVDs are disabled, external monitoring is required to guarantee correct device operation. 7. Reduced output/input capabilities below 4.2 V. See performance derating values in I/O pad electrical characteristics 8. VDD_HV_IO_JTAG supply is shorted with VDD_HV_OSC supply within package. 9. VDD_HV_PMC is shorted with VDD_HV_IO_MAIN in the package. 10. Flash read operation is supported for a minimum VDD_HV_FLA value of 3.0 V. Flash read, program, and erase operations are supported for a minimum VDD_HV_FLA value of 3.0 V. 11. This voltage can be measured on the pin but is not supplied by an external regulator. The Power Management Controller generates PORs based on this voltage. 12. VDD_HV_ADR_S must be between 4.5 V and 5.5 V for accurate reading of the device Temperature Sensor. 13. Full device lifetime without performance degradation 14. I/O and analog input specifications are only valid if the injection current on adjacent pins is within these limits. See Table 7: Absolute maximum ratings for maximum input current for reliability requirements. Table 12. Device operating conditions(1)(Continued) Symbol C Parameter Conditions Value Unit Min Typ Max |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |