Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

SL2305SC-1HT Datasheet(PDF) 7 Page - SpectraLinear Inc

Part # SL2305SC-1HT
Description  Low Jitter and Skew 10 to 140 MHz Zero Delay Buffer (ZDB)
PDF  11 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  SPECTRALINEAR [SpectraLinear Inc]
Direct Link  http://www.spectralinear.com
Logo SPECTRALINEAR - SpectraLinear Inc

SL2305SC-1HT Datasheet(HTML) 7 Page - SpectraLinear Inc

Back Button SL2305SC-1HT Datasheet HTML 3Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 4Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 5Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 6Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 7Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 8Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 9Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 10Page - SpectraLinear Inc SL2305SC-1HT Datasheet HTML 11Page - SpectraLinear Inc  
Zoom Inzoom in Zoom Outzoom out
 7 / 11 page
background image
Rev 1.4, May 25, 2007
Page 7 of 11
SL2305
External Components & Design Considerations
Typical Application Schematic
Comments and Recommendations
Decoupling Capacitor: A decoupling capacitor of 0.1 F must be used between VDD and VSS on the pins 6 and 4. Place
the capacitor on the component side of the PCB as close to the VDD pin as possible. The PCB trace to the VDD pin and to
the GND via should be kept as short as possible. Do not use vias between the decoupling capacitor and the VDD pin.
Series Termination Resistor: A series termination resistor is recommended if the distance between the outputs and the
load is over 1 ½ inch. The nominal impedance of the Clock outputs are about 30
. Use 20
resistor in series with the
output to terminate 50
trace impedance and place 20
resistor as close to the clock outputs as possible.
Zero Delay and Skew Control: All outputs and CLKIN pins should be loaded with the same load to achieve “Zero Delay”
between the CLKIN and the outputs. The CLKOUT pin is connected to CLKIN internally on-chip for internal feedback to
PLL, and sees an additional 2 pF load with respect to the clock pins. For applications requiring zero input/output delay, the
load at the all output pins including the CLKOUT pin must be the same. If any delay adjustment is required, the capacitance
at the CLKOUT pin could be increased or decreased to increase or decrease the delay between clocks and CLKIN.
For minimum pin-to-pin skew, the external load at the clock outputs must be the same.



Html Pages

1 2 3 4 5 6 7 8 9 10 11


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com