DocID023340 Rev 2

9/21

TS881

Electrical characteristics

21

Table 6. VCC =+5V, Tamb =+25 °C, VICM =VCC/2 (unless otherwise specified)(1)

Symbol

Parameter

Test conditions

Min.

Typ.

Max.

Unit

VIO

Input offset voltage(2)

-40 °C < Tamb < +125 °C

-6

1

6

mV

VIO Input offset voltage drift

-40 °C < Tamb < +125 °C

3

µV/°C

VHYST Input hysteresis voltage(3)

-40 °C < Tamb < +125 °C

1.6

3.1

4.2

mV

IIO

Input offset current(4)

-40 °C < Tamb < +125 °C

-10

-100

10

100

pA

IIB

Input bias current(4)

-40 °C < Tamb < +125 °C

-10

-100

110

100

pA

ICC

Supply current per operator

No load, output low, VID = -0.1 V

-40 °C < Tamb < +85 °C

-40 °C < Tamb < +125 °C

No load, output high, VID = +0.1 V

-40 °C < Tamb < +85 °C

-40 °C < Tamb < +125 °C

350

250

500

750

1350

400

650

1250

nA

ISC

Short-circuit current

Source

Sink

32

36

mA

VOH

Output voltage high

Isource =2mA

-40 °C < Tamb < +85 °C

-40 °C < Tamb < +125 °C

4.86

4.75

4.60

4.90

V

VOL

Output voltage low

Isink =2mA

-40 °C < Tamb < +85 °C

-40 °C < Tamb < +125 °C

95

130

170

280

mV

CMRR Common mode rejection ratio

0 < VICM < VCC

-40 °C < Tamb < +125 °C

55

78

dB

SVR

Supply voltage rejection

VCC = 1.2 V to 5 V

-40 °C < Tamb < +125 °C

65

80

dB

TPLH

Propagation delay

(low to high)

f=1kHz,CL =30 pF, RL =1M

Overdrive = 10 mV

-40 °C < Tamb < +125 °C

Overdrive = 100 mV

-40 °C < Tamb < +125 °C

7.8

2.6

13

22

3.4

4.1

µs

TPHL

Propagation delay

(high to low)

f=1kHz,CL =30 pF, RL =1M

Overdrive = 10 mV

-40 °C < Tamb < +125 °C

Overdrive = 100 mV

-40 °C < Tamb < +125 °C

8.9

2.7

16

19

3.5

4.2

µs

TR

Rise time (10% to 90%)

CL =30pF, RL =1M

160

ns

TF

Fall time (90% to 10%)

CL =30pF, RL =1M

150

ns

TON

Power-up time

1.1

1.5

ms

1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed

at the temperature range limits.

2. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to

change the output state in each direction).

3. The hysteresis is a built-in feature of the TS881 device. It is defined as the voltage difference between the trip points.

4. Maximum values are guaranteed by design.