| Electronic Components Datasheet Search |
|
DS481TM Datasheet(PDF) 3 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
DS481TM Datasheet(HTML) 3 Page - National Semiconductor (TI) |
|
3 / 8 page ![]() Switching Characteristics Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified (Notes 5, 9, 10) Symbol Parameter Conditions Min Typ Max Units t PLHD Driver Differential Propagation Delay — Low to High R L =54 Ω,C L = 100 pF 10 40 80 ns t PHLD Driver Differential Propagation Delay — High to Low 10 39 80 ns t SKEW Differential Skew |t PHLD −tPLHD|0 1 10 ns t r Driver Rise Time 325 50 ns t f Driver Fall Time 325 50 ns t ZH Driver Enable to Output High C L = 100 pF 50 200 ns t ZL Driver Enable to Output Low C L = 100 pF 65 200 ns t LZ Driver Disable from Output Low C L = 15 pF 80 200 ns t HZ Driver Disable from Output High C L = 15 pF 80 200 ns t PSH Driver Enable from Sleep C L = 100 pF 70 98 250 ns Mode to Output High (Note 12) (Figures 5, 6) t PSL Driver Enable from Sleep C L = 100 pF 70 98 250 ns Mode to Output Low (Note 12) (Figures 7, 8) t PLHD Receiver Differential Propagation Delay — Low to High C L = 15 pF (RO) 30 190 400 ns t PHLD Receiver Differential Propagation Delay — High to Low 30 210 400 ns t SKEW Differential Skew |t PHLD −tPLHD| 0 20 50 ns t ZH Receiver Enable to Output High C L = 15 pF 45 150 ns t ZL Receiver Enable to Output Low 40 150 ns t LZ Receiver Disable from Output Low 50 150 ns t HZ Receiver Disable from Output High 55 150 ns t PSH Receiver Enable from Sleep C L = 15 pF 70 97 250 ns Mode to Output High (Note 12) (Figures 11, 13) t PSL Receiver Enable from Sleep C L = 15 pF 70 95 250 ns Mode to Output Low (Note 12) (Figures 11, 12) t SLEEP Time to Sleep (Device) DE = L and RE (Note 1) = H 50 600 ns (Figure 14) f max Maximum Data Rate (Note 11) 2.0 Mbps Note 3: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. Note 4: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD1/2/3and VID. Note 5: All typicals are given for: VCC = +5.0V, TA = +25˚C. Note 6: ∆|VOD| and ∆|VOC| are changes in magnitude of V OD and VOC respectively, that occur when the input changes state. Note 7: IIN2 includes the receiver input current and driver TRI-STATE leakage current. Note 8: Supply current specification is valid for loaded transmitters when DE = 0V or enabled (DE = H) with no load. Note 9: f = 1 MHz, tr and tf ≤ 6 ns, ZO =50Ω. Note 10: CL includes jig and probe capacitance. Note 11: fmax is the guaranteed data rate for 50 ft of twisted pair cable. f max may be conservatively determined from the ratio of driver transition time (tr) to the data rate unit interval (1/fmax). Using a 10% ratio yields fmax = (0.1)/50 ns = 2.0 Mb/s. Higher data rates may be supported by allowing larger ratios. Note 12: For enable from sleep mode delays DE = L and RE (Note 1) = H for greater than 600 ns prior to test (device is in sleep mode). www.national.com 3 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |