| Electronic Components Datasheet Search |
|
M40SZ100WMQ6 Datasheet(PDF) 12 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
M40SZ100WMQ6 Datasheet(HTML) 12 Page - STMicroelectronics |
|
12 / 19 page ![]() M40SZ100Y, M40SZ100W 12/19 Battery Low Pin The M40SZ100Y/W automatically performs bat- tery voltage monitoring upon power-up, and at fac- tory-programmed time intervals of at least 24 hours. The Battery Low (BL) pin will be asserted if the battery voltage is found to be less than approx- imately 2.5V. The BL pin will remain asserted until completion of battery replacement and subse- quent battery low monitoring tests, either during the next power-up sequence or the next scheduled 24-hour interval. If a battery low is generated during a power-up se- quence, this indicates that the battery is below 2.5V and may not be able to maintain data integrity in the SRAM. Data should be considered suspect, and verified as correct. A fresh battery should be installed. If a battery low indication is generated during the 24-hour interval check, this indicates that the bat- tery is near end of life. However, data is not com- promised due to the fact that a nominal VCC is supplied. In order to insure data integrity during subsequent periods of battery back-up mode, the battery should be replaced. The M40SZ100Y/W only monitors the battery when a nominal VCC is applied to the device. Thus applications which require extensive durations in the battery back-up mode should be powered-up periodically (at least once every few months) in or- der for this technique to be beneficial. Additionally, if a battery low is indicated, data integrity should be verified upon power-up via a checksum or other technique. The BL pin is an open drain output and an appropriate pull-up resistor to VCC should be chosen to control the rise time. Power-fail Input/Output The Power-Fail Input (PFI) is compared to an in- ternal reference voltage (independent from the VPFD comparator). If PFI is less than the power-fail threshold (VPFI), the Power-Fail Output (PFO) will go low. This function is intended for use as an un- der-voltage detector to signal a failing power sup- ply. Typically PFI is connected through an external voltage divider (see Figure 7, page 5) to either the unregulated DC input (if it is available) or the reg- ulated output of the VCC regulator. The voltage di- vider can be set up such that the voltage at PFI falls below VPFI several milliseconds before the regulated VCC input to the M40SZ100Y/W or the microprocessor drops below the minimum operat- ing voltage. During battery back-up, the power-fail comparator turns off and PFO goes (or remains) low. This oc- curs after VCC drops below VPFD(min). When pow- er returns, PFO is forced high, irrespective of VPFI for the write protect time (tREC), which is the time from VPFD (max) until the inputs are recognized. At the end of this time, the power-fail comparator is enabled and PFO follows PFI. If the comparator is unused, PFI should be connected to VSS and PFO left unconnected. VCC Noise And Negative Going Transients ICC transients, including those produced by output switching, can produce voltage fluctuations, re- sulting in spikes on the VCC bus. These transients can be reduced if capacitors are used to store en- ergy which stabilizes the VCC bus. The energy stored in the bypass capacitors will be released as low going spikes are generated or energy will be absorbed when overshoots occur. A ceramic by- pass capacitor value of 0.1µF (as shown in Figure 13) is recommended in order to provide the need- ed filtering. In addition to transients that are caused by normal SRAM operation, power cycling can generate neg- ative voltage spikes on VCC that drive it to values below VSS by as much as one volt. These negative spikes can cause data corruption in the SRAM while in battery backup mode. To protect from these voltage spikes, STMicroelectronics recom- mends connecting a schottky diode from VCC to VSS (cathode connected to VCC, anode to VSS). Schottky diode 1N5817 is recommended for through hole and MBRS120T3 is recommended for surface mount. Figure 13. Supply Voltage Protection AI00622 VCC 0.1 µF DEVICE VCC VSS |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |