M58LV064A datasheet(21/65 Pages) STMICROELECTRONICS

21 / 65 page

21/65

M58LV064A, M58LV064B

Burst Configuration Register

The Burst Configuration Register is used to config-

ure the type of bus access that the memory will

perform.

The Burst Configuration Register is set through

the Command Interface and will retain its informa-

tion until it is re-configured, the device is reset, or

the device goes into Reset/Power-Down mode.

The Burst Configuration Register bits are de-

scribed in Table 5. They specify the selection of

the burst length, burst type, burst X and Y laten-

cies and the Read operation.

Read Select Bit (M15). The

Read

Select

bit,

M15, is used to switch between asynchronous and

synchronous Bus Read operations. When the

Read Select bit is set to ’1’, Bus Read operations

are asynchronous; when the Read Select but is

set to ’0’, Bus Read operations are synchronous.

On reset or power-up the Read Select bit is set

to’1’ for asynchronous accesses.

X-Latency Bits (M14-M11). The X-Latency bits

are used during Synchronous Bus Read opera-

tions to set the number of clock cycles between

the address being latched and the first data be-

coming available. For correct operation the X-La-

tency bits can only assume the values in Table 5,

Burst Configuration Register. The X-Latency bits

should also be selected in conjunction with Table

8, Burst Performance to ensure valid settings.

Y-Latency Bit (M9). The Y-Latency bit is used

during Synchronous Bus Read operations to set

the number of clock cycles between consecutive

reads. The Y-Latency value depends on both the

X-Latency value and the setting in M9.

When the Y-Latency is 1 the data changes each

clock cycle; when the Y-Latency is 2 the data

changes every second clock cycle. See Table 5,

Burst Configuration Register and Table 8, Burst

Performance, for valid combinations of the Y-La-

tency, the X-Latency and the Clock frequency.

Valid Data Ready Bit (M8). The

Valid

Data

Ready bit controls the timing of the Valid Data

Ready output pin, R. When the Valid Data Ready

bit is ’0’ the Valid Data Ready output pin is driven

Low for the active clock edge when invalid data is

output on the bus. When the Valid Data Ready bit

is ’1’ the Valid Data Ready output pin is driven Low

one clock cycle prior to invalid data being output

on the bus.

Burst Type Bit (M7). The Burst Type bit is used

to configure the sequence of addresses read as

sequential or interleaved. When the Burst Type bit

is ’0’ the memory outputs from interleaved ad-

dresses; when the Burst Type bit is ’1’ the memory

outputs from sequential addresses. See Tables 6

and 7, Burst Type Definition, for the sequence of

addresses output from a given starting address in

each mode.

Valid Clock Edge Bit (M6). The Valid Clock Edge

bit, M6, is used to configure the active edge of the

Clock, K, during Synchronous Burst Read opera-

tions. When the Valid Clock Edge bit is ’0’ the fall-

ing edge of the Clock is the active edge; when the

Valid Clock Edge bit is ’1’ the rising edge of the

Clock is active.

Latch Enable Bit (M3). The Latch Enable bit is

used to select between Asynchronous Random

Read and Asynchronous Latch Enable Controlled

Read. When the Latch Enable bit is set to ‘0’ Ran-

dom read is selected; when it is set to ‘1’ Latch En-

able Controlled Read is selected. To enable these

Asynchronous Read configurations M15 must be

set to ‘1’.

Burst Length Bit (M2-M0). The Burst Length bits

set the maximum number of Words or Double-

Words that can be output during a Synchronous

Burst Read operation before the address wraps.

Table 5, Burst Configuration Register gives the

valid combinations of the Burst Length bits that the

memory accepts; Tables 6 and 7, Burst Type Def-

inition, give the sequence of addresses output

from a given starting address for each length.

M10, M5 and M4 are reserved for future use.

M58LV064A Datasheet(PDF) 21 Page - STMicroelectronics

M58LV064A Datasheet(HTML) 21 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

Datasheet Download

Link URL