| Electronic Components Datasheet Search |
|
M58LW064AT Datasheet(PDF) 12 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
M58LW064AT Datasheet(HTML) 12 Page - STMicroelectronics |
|
12 / 53 page ![]() M58LW064A, M58LW064B 12/53 DEVICE OPERATIONS See Tables 5, 6, 7 and 10. Address Latch. An address is latched on the ris- ing edge of the Latch Enable L input for Asynchro- nous Latch Enable Controlled Read. For Asynchrouns Latch Enable Controlled Write, the address is latched on the rising edge of Chip En- able E, Write Enable W or Latch Enable L, which- ever occurs first. For Synchronous Burst Read the address is latched on the first valid Burst Clock K edge when Latch Enable L is at Low, or on the rising edge of Latch Enable L, whichever occurs first. Asynchronous Random Read. Asynchronous Random Read outputs the contents of the Array. Both Chip Enable E and Output Enable G must be Low in order to read the output of the memory. By first writing the appropriate Instruction, the Electronic Signature (RSIG), the Status Register (RSR), the Read Query Instruction (RCFI) or the Block Protection Status (RSIG) can be read. Asynchronous Random Read is the default read mode which the device enters on power-up or on return from Reset/Power-down. Asynchronous Page Read. Asynchronous Page Read may be used for Random or Latch En- able Controlled Reads of the Array, which are per- formed independent of the Burst Clock signal. A page has a size of 4 Words or 2 Double-Words and is addressed by the address inputs A1 and A2 in the x16, or A2 only in the x32 organisation. Data is read internally and stored in the Page Buffer. The page read starts when both Chip Enable E and Output Enable G are Low. The first data is in- ternally read and is output after the normal access time tAVQV. Successive Words or Double-Words can be read with a much reduced access time of tAVQV1 by changing only the low address bits. Synchronous Burst Read. The memory sup- ports different types of burst access using a Burst Configuration Register to configure the burst type, length and latency. In continuous burst read, one burst read operation can access the entire memory sequentially by keeping the Burst Address Advance B Low for the appropriate number of clock cycles. At the end of the memory address space the burst read restarts from the beginning at address 000000h. Synchronous Burst Read is activated when the Burst Clock K input is clocking and Chip Enable E is Low. The burst start address is latched and loaded into the internal Burst Address Counter on the valid Burst Clock K edge (rising or falling de- pending on the M6 bit value for the Burst Clock Edge Configuration in the Burst Configuration Register) when Latch Enable L is Low, or upon the rising edge of Latch Enable L when the Burst Clock K is valid. After an initial memory latency time, the memory outputs data each clock cycle (or two clock cycles depending on M9 bit value de- fined in the Burst Configuration Register). The Burst Address Advance B input controls the mem- ory burst output. The second burst output is on the next clock valid edge after the Burst Address Ad- vance B has been pulled Low. The Valid Data Ready output signal R monitors if the memory burst boundary is exceeded and the Burst Controller of the microprocessor needs to in- sert wait states. When Valid Data Ready R is Low on the active clock edge, no new data is available and the memory does not increment the internal address counter at the active clock edge even if Burst Address Advance B is Low. Synchronous Burst Read will be suspended when Burst Address Advance B is High. The Valid Data Ready signal R may be configured (by bit M8 of Burst Configuration Register) to be valid immedi- ately at the valid clock edge or one data cycle be- fore the valid clock edge. To increase the data throughput the device has been built with an internal pipelined architecture allowing the user to enter a burst read input com- mand and the next starting address location to be read while the device is filling the output data bus with its current burst content. This pipelined struc- ture is intended to produce no wait-states on the output data bus for successive burst read mode operations. Asynchronous and Latch Enable Controlled Write. Asynchronous Write is used to give com- mands to the Command Interface for Instructions to the memory or to latch addresses and input data to be programmed. To perform any Instruction the Command Interface is activated starting with a write cycle. A write cycle is also required give the Instruction to clear the Status Register informa- tion. Two write cycles are needed to define the Block Erase and the Write to Buffer and Program Instructions. The first write cycle defines the In- struction selection and the second indicates the appropriate block address to be erased for the Block Erase instruction, or the address locations to program with the number of Words or Double- Words in the Write to Buffer and Program Instruc- tion. An Asynchronous Write is initiated when Chip En- able E, Write Enable W and Latch Enable L are Low with Output Enable G High. Commands and Input Data are latched on the rising edge of Chip Enable E or Write Enable W, whichever occurs first. For an Asynchronous Latch Enable Con- trolled Write the address is latched on the rising edge of Latch Enable L, Write Enable W or Chip Enable E, whichever occurs first. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |