RA4T1 datasheet(24/89 Pages) RENESAS

24 / 89 page

ICC Max. = 0.24 × f + 37 (max. operation in high-speed mode)

ICC Typ. = 0.07 × f + 2.75 (normal operation in high-speed mode, all peripheral clocks disabled)

ICC Typ. = 0.1 × f + 1.71 (low-speed mode)

ICC Max. = 0.05 × f + 37 (sleep mode)

Note 4. This does not include the BGO operation.

Note 5. Supply of the clock signal to peripherals is stopped in this state. This does not include the BGO operation.

Note 6. FCLK, PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (1.56 MHz).

Note 7. FCLK, PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (3.125 MHz).

Note 8. Reference value

Note 9. When the MCU is in Software Standby mode or the MSTPCRD.MSTPD16 (12-Bit A/D Converter 0 Module Stop bit) is in the

module-stop state.

Note 10. FCLK, PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (15.6 kHz).

Note 11. PCLKA, PCLKB, PCLKC, and PCLKD are set to divided by 64 (512 Hz). FCLK is the same frequency as that of ICLK.

Note 12. PLL output frequency = 100MHz.

Note 13. PLL output frequency = 200MHz.

Note 14. For more information on the DBSBYCR register, see Deep Software Standby Control Register (DPSBYCR).

Table 2.8

Coremark and normal mode current

Parameter

Symbol

Typ

Unit

Test conditions

Supply Current*1

Coremark*2 *3

ICC

µA/MHz

ICLK = 100 MHz

PCLKA =

PCLKB =

PCLKC =

PCLKD =

FCLK =

1.563 MHz

Normal mode

All peripheral

clocks disabled,

cache on,

while (1) code

executing from

flash*2 *3

All peripheral

clocks disabled,

cache off,

while (1) code

executing from

flash*2 *3

Note 1. Supply current values are with all output pins unloaded and all input pull-up MOSs in the off state.

Note 2. Supply of the clock signal to peripherals is stopped in this state. This does not include the BGO operation.

Note 3. PLL output frequency = 100MHz.

Average vaAverage value of the tested upper-limit samples during product evaluation.

-40

1.40

2.19

3.11

7.40

10.04

24.53

105

15.28

35.93

125

22.99

52.13

Figure 52.2 Temperature dependency in Software Standby mode (reference data)

0.1

1.0

10.0

100.0

‐40

‐20

100

Ta (℃)

Average value of the tested middle samples during product evaluation.

Average value of the tested upper‐limit samples during product evaluation.

Figure 2.2

Temperature dependency in Software Standby mode (reference data)

RA4T1 Datasheet

2. Electrical Characteristics

R01DS0415EJ0140 Rev.1.40

May 29, 2026

Page 24 of 89

RA4T1 Datasheet(PDF) 24 Page - Renesas Technology Corp

RA4T1 Datasheet(HTML) 24 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

Datasheet Download

Link URL