ELECTRICAL GROUP

Printed in U.S.A.

For Pricing and Further Information –

Contact your local authorized

PANDUIT Distributor or Sales Office

©Panduit Corp. 2001

ALL RIGHTS RESERVED

WORLDWIDE SUBSIDIARIES AND SALES OFFICES

This warranty is made in lieu of and excludes all other warranties, expressed or implied. THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE ARE SPECIFICALLY

EXCLUDED. Neither seller nor manufacturer shall be liable for any other injury, loss or damage, whether

direct or consequential, arising out of the use of, or the inability to use, the product.

The information contained in this literature is based on our experience to date and is believed to be reliable.

It is intended as a guide for use by persons having technical skill at their own discretion and risk. We do not

guarantee favorable results or assume any liability in connection with its use. Dimensions contained herein

are for reference purposes only. For specific dimensional requirements consult the factory. This publication

is not to be taken as a license to operate under, or a recommendation to infringe any existing patents. This

supersedes and voids all previous literature, etc.

WORLD HEADQUARTERS

PANDUIT CORP.

Tinley Park, Illinois, USA

Phone: 800-777-3300

Fax:

708-532-1811

Email: info@panduit.com

Internet: www.panduit.com

EUROPEAN HEADQUARTERS

PANDUIT EUROPE LTD.

London, UK

Phone: 44 (0) 208-601-7200

PANDUIT CANADA

Div. of PANDUIT CORP.

Markham, Ontario

Phone: 905-475-6922

PANDUIT MEXICO/ LATIN AMERICA &

CARIBBEAN

Phone: (52) 3 666-2501

ASIAN HEADQUARTERS

PANDUIT SINGAPORE PTE. LTD.

Republic of Singapore

Phone: (65) 379 6700

Our products are warranted to be free from defects in material and workmanship at the time of sale but our

obligation under this warranty is limited to the replacement of any product proved to be defective within 6

months (for product) or 90 days (for tools) from the date of delivery. Tool warranty is void if Panduit tools

are modified, altered or misused in any way. Use of Panduit tooling with any product other than the

specified Panduit products for which the tool was designed, constitutes misuse. Before using, user shall

determine the suitability of the product for his intended use and user assumes all risk and liability

whatsoever in connection therewith.

SA117N357-WA

PANDUIT

®

Stackable Cable Rack Spacers

General Installation Instructions for Stackable Cable Rack Spacers

1.

Secure bottom level of Stackable Cable Rack Spacer to the application surface, i.e. ladder rung with two standard

cross-section PANDUIT® PAN-TY™ Cable Ties (View 1, 2, and 3).

2. Install cable or cable bundles into each of the cable retaining areas (View 1, 2, and 3).

3. Secure cable to the cable retaining posts (View 1, 2, and 3) with PANDUIT PAN-TY Cable Ties, BELT-TY™ IN-LINE Cable Ties,

or TAK-TY™ Hook & Loop Cable Ties up to 0.33" in width.

4. Installation of the next level of Stackable Cable Rack Spacers is accomplished by sliding the male dovetail into the female

dovetail slot (View 4, 5, and 6). The latch/latches will lock the parts into position. To unlock these parts, use a screwdriver or a

small tool to release latch/latches and slide in opposite direction.

5. Repeat steps 2, 3, and 4 until a maximum stack height is achieved. PANDUIT recommends a maximum stack height of five

for the CRS6-X and CRS1-X. A maximum stack height of four is recommended for the CRS4-125-X, and CRS1-125-X.

Stackable Cable Rack Spacers are reversible to allow cable retaining posts to be alternated (View 7).

•

A typical PANDUIT PAN-TY ® Cable Tie part number is PLT2S-C0 or PLT2S-M60.

•

A typical PANDUIT BELT-TY

™ IN-LINE Cable Tie part number is ILT2S-M0.

•

A typical PANDUIT TAK-TY

™ Hook & Loop part number is HLM-15R0.

•

Refer to PANDUIT Network Connectivity Systems Catalog (SA101N423A-OP) for more information.

View 1 (CRS6-X)

View 2 (CRS1-X and CRS1-125-X)

View 3 (CRS4-125-X)

View 4

View 5

View 6

View 7