R8C2K datasheet(416/471 Pages) RENESAS

416 / 471 page

R8C/2K Group, R8C/2L Group

21. Reducing Power Consumption

Rev.1.10

Dec 21, 2007

Page 399 of 450

REJ09B0406-0110

21.2.8

Reducing Internal Power Consumption

When the MCU enters wait mode using low-speed on-chip oscillator mode, internal power consumption can be

reduced by using the VCA20 bit in the VCA2 register. Figure 21.1 shows the Handling Procedure of Internal

Power Low Consumption Using VCA20 Bit. To enable internal power low consumption by the VCA20 bit,

follow Figure 21.1 Handling Procedure of Internal Power Low Consumption Using VCA20 Bit.

Figure 21.1

Handling Procedure of Internal Power Low Consumption Using VCA20 Bit

NOTES:

1. Execute this routine to handle all interrupts generated in wait mode.

However, this does not apply if it is not necessary to start the high-speed clock or high-speed on-chip oscillator during the interrupt routine.

2. Do not set the VCA20 bit to 0 with the instruction immediately after setting the VCA20 bit to 1. Also, do not do the opposite.

3. When the VCA20 bit is set to 1, do not set the CM10 bit to 1 (stop mode).

4. When entering wait mode, follow 10.6.2 Wait Mode.

Handling procedure of internal power

low consumption enabled by VCA20 bit

Enter low-speed on-chip oscillator mode

Stop XIN clock and high-speed on-chip

oscillator clock

VCA20

← 1 (internal power low consumption

enabled)(2, 3)

Enter wait mode(4)

VCA20

← 0 (internal power low consumption

disabled)(2)

Start XIN clock or high-speed on-chip

oscillator clock

(Wait until XIN clock oscillation stabilizes)

Enter high-speed clock mode or

high-speed on-chip oscillator mode

In interrupt routine

VCA20

← 0 (internal power low consumption

disabled)(2)

Start XIN clock or high-speed on-chip

oscillator clock

Enter high-speed clock mode or

high-speed on-chip oscillator mode

Enter low-speed on-chip oscillator mode

Exit wait mode by interrupt

Stop XIN clock and high-speed on-chip

oscillator clock

VCA20

← 1 (internal power low consumption

enabled)(2, 3)

Interrupt handling completed

Step (1)

Step (2)

Step (3)

Step (4)

Step (5)

Step (6)

Step (7)

Step (8)

Step (5)

Step (6)

Step (7)

Step (8)

(Wait until XIN clock oscillation stabilizes)

Step (1)

Step (2)

Step (3)

If it is necessary to start

the high-speed clock or

the high-speed on-chip

oscillator in the interrupt

routine, execute steps (5)

to (7) in the interrupt

routine.

If the high-speed clock or

high-speed on-chip

oscillator is started in the

interrupt routine, execute

steps (1) to (3) at the last of

the interrupt routine.

(Note 1)

Interrupt handling

VCA20: Bit in VCA2 register

R8C2K Datasheet(PDF) 416 Page - Renesas Technology Corp

R8C2K Datasheet(HTML) 416 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL