HD6432351 datasheet(637/1025 Pages) RENESAS

637 / 1025 page

Section 13 Serial Communication Interface (SCI)

Rev. 3.00 Sep 15, 2006 page 603 of 988

REJ09B0330-0300

Yes

<End>

[1]

Initialization

Start transmission/reception

[5]

Error processing

[3]

Read receive data in RDR, and

clear RDRF flag in SSR to 0

Yes

ORER = 1

All data received?

[2]

Read TDRE flag in SSR

Yes

TDRE = 1

Write transmit data to TDR and

clear TDRE flag in SSR to 0

Yes

RDRF = 1

Read ORER flag in SSR

[4]

Read RDRF flag in SSR

Clear TE and RE bits in SCR to 0

Note: When switching from transmit or receive operation to simultaneous

transmit and receive operations, first clear the TE bit and RE bit to

0, then set both these bits to 1 simultaneously.

[1]

[2]

[3]

[4]

[5]

SCI initialization:

The TxD pin is designated as the

transmit data output pin, and the

RxD pin is designated as the

receive data input pin, enabling

simultaneous transmit and receive

operations.

SCI status check and transmit data

write:

Read SSR and check that the

TDRE flag is set to 1, then write

transmit data to TDR and clear the

TDRE flag to 0.

Transition of the TDRE flag from 0

to 1 can also be identified by a TXI

interrupt.

Receive error processing:

If a receive error occurs, read the

ORER flag in SSR , and after

performing the appropriate error

processing, clear the ORER flag to

0. Transmission/reception cannot be

resumed if the ORER flag is set to

SCI status check and receive data

read:

Read SSR and check that the

RDRF flag is set to 1, then read the

receive data in RDR and clear the

RDRF flag to 0. Transition of the

RDRF flag from 0 to 1 can also be

identified by an RXI interrupt.

Serial transmission/reception

continuation procedure:

To continue serial transmission/

reception, before the MSB (bit 7) of

the current frame is received, finish

reading the RDRF flag, reading

RDR, and clearing the RDRF flag to

0. Also, before the MSB (bit 7) of

the current frame is transmitted,

read 1 from the TDRE flag to

confirm that writing is possible.

Then write data to TDR and clear

the TDRE flag to 0.

Checking and clearing of the TDRE

flag is automatic when the DMAC or

DTC is activated by a transmit data

empty interrupt (TXI) request and

data is written to TDR. Also, the

RDRF flag is cleared automatically

when the DMAC or DTC is activated

by a receive data full interrupt (RXI)

request and the RDR value is read.

Figure 13.20 Sample Flowchart of Simultaneous Serial Transmit and Receive Operations

HD6432351 Datasheet(PDF) 637 Page - Renesas Technology Corp

HD6432351 Datasheet(HTML) 637 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL