| Electronic Components Datasheet Search |
|
CS5376A Datasheet(PDF) 72 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5376A Datasheet(HTML) 72 Page - Cirrus Logic |
|
72 / 106 page ![]() CS5376A 72 DS612F4 During a transaction, bits in SPI2CMD are output MSB first, with data in SPI2DAT written or read following. 20.3.3 SPI 2 Data Register The SPI2DAT register (0x12) is a 24-bit digital fil- ter register containing three SPI data bytes. Data in SPI2DAT is always LSB aligned, with 1-byte data written or received using the low byte, 2-byte data written or received using the middle and low bytes, and 3-byte data written or received using all three bytes. Data in SPI2DAT is written or read after writing the command and address bytes from the SPI2CMD register. 20.4 SPI 2 Transactions The SPI 2 port operates as an SPI master to perform write and read transactions with serial slave periph- erals. The exact format of the SPI transactions de- pends on the SPI mode, selected using the SCKPO and SCKPH bits in the SPI2CTRL register. Write Transactions Write transactions start by writing an SPI ‘write’ (0x02) opcode and an 8-bit destination address into the SPI2CMD register and the output data value to the SPI2DAT register. Writing the D2SREQ bit in the SPI2CTRL register initiates the SPI 2 transac- tion based on the SPI2CTRL configuration. A write transaction outputs 1 or 2 bytes from the SPI2CMD register followed by 1, 2, or 3 bytes from the SPI2DAT register. Write transactions are therefore a minimum of 1 byte (DNUM = 0) and a maximum of 5 bytes (DNUM = 4). The SPI 2 port uses the DNUM bits in the SPI2CTRL register to determine the total number of bytes to send during a write transaction. Write transactions are not required to use standard SPI commands. If serial peripherals use non-stan- dard write commands they can be written into SPI2CMD and SPI2DAT as required. Read Transactions Read transactions start by writing an SPI ‘read’ (0x03) opcode and an 8-bit source address to the SPI2CMD register. Writing the D2SREQ bit in the SPI2CTRL register initiates the SPI 2 transaction based on the SPI2CTRL configuration, with the data value automatically received into the SPI2DAT register. A read transaction outputs 2 bytes from the SPI2CMD register and can receive 1, 2, or 3 bytes into the SPI2DAT register. Read transactions are a minimum of 3 bytes (DNUM = 2) and a maximum of 5 bytes (DNUM = 4). The SPI 2 port uses the DNUM bits in the SPI2CTRL register to determine the total number of bytes to send and receive during a read transaction. Read transactions are not required to use standard SPI commands. If serial peripherals use non-stan- dard read commands they can be written to the SPI2CMD register, as long as they conform to the format of 2 bytes out with 1, 2, or 3 bytes in. SPI Modes The SPI mode for the SPI 2 port is selected in the SPI2CTRL register using the SCKPO and SCKPH bits. The most commonly used SPI modes are mode 0 and mode 3, both of which define the serial clock with data valid on rising edges and transition- ing on falling edges. In SPI mode 0, the SCK2 serial clock is defined ini- tially in a low state. Output data on the SO pin is valid immediately after the chip select pin goes low, and the first rising edge of SCK2 latches valid data. In SPI mode 3, the SCK2 serial clock is defined ini- tially in a high state. Output data on the SO pin is invalid until the initial falling edge of SCK2, and the first rising edge of SCK2 latches valid data. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |